Hello Jim. Thanks for the 'permission' I'll try and information gather for a couple of days and then send them something fairly complete by the end of the week. Yes, a recording from Dave would be ve
Hello Chaps. Well, I think we have an opportunity to influence the future of the Loran project at Rugby. I made a complaint about the interference to the Loarn organisation and they have put the Trin
In a message dated 30/06/2005 21:55:29 GMT Standard Time, [email protected] writes: Thanks Laurie. I was playing with a friend's new 756 PRO III (he won it at Dayton this year!!) and it se
In a message dated 03/10/2005 10:51:36 GMT Standard Time, [email protected] writes: in the LF Experimenter's handbook, using the same number of turns. > These capacitors are running very hot too
In a message dated 04/11/2005 16:57:25 GMT Standard Time, [email protected] writes: Im hoping to erect a reasonably large but lightweight temp 60m vertical here in the near future but ne
In a message dated 03/11/2005 16:23:39 GMT Standard Time, [email protected] writes: Hi Lf's in all circuit diagrams I find filters like 12nF-->54uH-->27nF-->54uH-->12nF here is the 3db point at 250k
In a message dated 26/02/2006 20:56:56 GMT Standard Time, [email protected] writes: Greetings all, This post may be a bit off-frequency but it may be nice to check the accuracy of the "master oscilla
In a message dated 25/02/2006 21:05:04 GMT Standard Time, [email protected] writes: Hello Mal, QRS doesn't work with a "pure" USB port. Unlike the serial and parallel port the lines of a US
In a message dated 17/03/2006 07:34:35 GMT Standard Time, [email protected] writes: hello Dick, check this catalog see at www.reichelt.de ( Electronik- supplier near Wilhelmshaven ) may be thats us
In a message dated 16/03/2006 11:28:43 GMT Standard Time, [email protected] writes: Hello ....... I am looking for a source to buy 3C90 (or 3C85) toroids, 58mm diameter. Up til now I can only find '
In a message dated 05/03/2006 12:38:28 GMT Standard Time, [email protected] writes: Hi Martin, as Dave says the most cost effective way would be Albertos mod, even if you have to pay someone
Hello all. I had a request from OZ8RF to see if I could supply some of the transformers for Alberto's modicication to the TS950. Well they seem happy to supply them to me but not ship to Denmark. If
In a message dated 07/03/2006 20:21:20 GMT Standard Time, [email protected] writes: For rugby test schedules, contact Twickenham Stadium? 73, Bob ZL2CA I drove past it this evening. No one was home
Hello MArtin. Yes, I'm listening. I've just built 6 of the pre-amps this weekend. Two are packed to go to DL and one to Oaklahoma. They are aligned to 136.5 and need a 12 - 14V supply. It's an assemb
In a message dated 26/04/2006 21:14:42 GMT Standard Time, [email protected] writes: Also visible is the antennarelay as well as a part of the driver unit. Maybe David may recognize the 3C90 core, hi
In a message dated 30/04/2006 21:43:09 GMT Standard Time, [email protected] writes: Hi Dick, LF Group, What power supply voltage will you be using for your new TX, and what RF power do you
In a message dated 11/06/2006 21:03:30 GMT Standard Time, [email protected] writes: So, perhaps I should trow out this core and use an air wound coil to transform 50 to 100-300 Ohm. Any suggestions
Thanks John and Alan for the update. - Must pay more attention! I wondered if it was a crystal based TX......But obviously a much more practical reason for going to 136.3. 73 from ( a sunny at last)
Isn't QRSS 137+ or 135.7 ish on the bandplan? Not that there's much CW activity these days, but I would have thought the remote receivers are all set up for other frequencies. David In a message date
