Hello Vincent, Thursday, November 19, 2015 That looks a hefty beast, never seen one though. I do have a R140 amp in the loft, awaiting power supply and control board completion. I might e-mail the Po
Hello Rik, Thursday, November 19, 2015 Thanks Rik, will place it at the bottom of the tuning coil then, I need to do some testing on the bench to recreate the resonance and get the variometer to span
Hello Rik, Thursday, November 19, 2015 Whilst you experts argue the technical niceties of the challenge, let me ask what might be a simple question to you guys. What is the minimum number of two cont
Hello Andy, Thursday, November 19, 2015 Thanks Andy, I have just put my coat and boots by the door <LOL> -- Best regards, Chris 2E0ILY mailto:[email protected]
19 November 2015 I am trying to run the script from this site, http://radio.g4hsk.co.uk/digi-modes/qrss-grabber/ and it will upload grabs but I am unsure of an Argo setting. Under Capture - Setup the
Hello Graham, Thursday, November 19, 2015 Probably, but my loop works very well on HF, would be sad to lose it to just LF usage. If I had to run dual antennas I would probably keep the loop as HF and
Hello Chris, Thursday, November 19, 2015 OK, I think I have mastered it now, but would still like to know what the Capture - Setup - Lock Sequence Number tick boxes are supposed to do, thanks. -- Bes
Hello DK7FC, Thursday, October 29, 2015 I have breadboarded the motor drive circuit and tested it with 2 one and a half volt cells centre tapped and 1k pot to simulate the phase change input. The dri
Hello Hugh, Saturday, November 21, 2015 Thanks for the details of the small relay. I think, in view of the number of relays i would need, the voltages involved, and the price of the things I may have
Hello DK7FC, Saturday, November 21, 2015 I'll run it off a separate supply then, thanks Stefan, or maybe off an accumulator, I have loads of lightweight race car gel batteries that get changed solely
23 November 2015 Murray is unable to access this forum, and if possible could anyone help him out, I know it's unmoderated and in a parlous state, but here is his message: ~~~~~~~~~~~~~~~~~~~~~~~~~~~
Hello Alan, Monday, November 23, 2015 Thanks Alan, hopefully Murray will be able to read this, but if not I will copy / paste it to him by direct e-mail. -- Best regards, Chris 2E0ILY mailto:chris@ch
25 November 2015 As I am under a lot of pressure with work I was thinking of a quick and simple way to improve my aerial. Better ground wires under the perimeter of my horizontal quad loop "top hat"
Hello Alan, Wednesday, November 25, 2015 Thank you Alan, once again. Sorry for the late reply, work is my excuse! Where do the hours go? -- Best regards, Chris 2E0ILY mailto:[email protected]
06 December 2015 I have my TS-590 transceiver locked to a Trimble Thunderbolt 10MHz reference, using the device from here: http://www.vk3hz.net/XRef/XRef_Home.html#XRef-Vx It's the X-Ref Versatile on
Hello Paul, Sunday, December 6, 2015 Hi Paul, thanks for your detailed reply. Taking things in the order below, the 590 has a built in USB sound card that i use for digital modes, but i need to look
Hello Paul, Sunday, December 6, 2015 I have had a poke through the schematics and it uses a PCM2903B USB chip with its own external 12MHz xtal, so it's not tied to the master oscillator... :( I find
Hello Andy, Sunday, December 6, 2015 So how would I test for these "slippages" or even recognize if they were occurring Andy? What sound cards are you EbNauters using that might have good Win7 64 bit
08 December 2015 Now well on with my motor drive variometer for 136kHz, my question is how far away from the loading coil base can I realistically insert the motor drive variometer. I am thinking of
Hello Chris, Friday, December 11, 2015 What appears to be happening is you have some spots (or not, as the case may be), but even after 2 minutes have passed the application is unable to contact the
