Hello Steinar, Markus, LF,
That is all very strage. After the transmission in the afternoon and
evening using JT9-30 i think i will go back to the usual modes until Joe
has some good ideas :-)
Have to work on the step down converter that works better and better now!
73, cu, Stefan
Am 30.10.2012 14:37, schrieb Steinar Aanesland:
Hi Markus
I had no luck with Stefan last evening , no asterisks and no echo
2315 5 -29 -0.8 1432.73 0.00
2320 10 -12 0.2 1439.73 0.00
2325 5 -29 0.4 1428.55 0.00
2330 10 -12 0.0 1439.73 0.00
2335 4 -30 0.0 1420.20 0.00
2340 10 -14 0.2 1439.73 0.00
2345 6 -29 0.2 1427.61 0.00
2350 10 -19 0.2 1439.73 0.00
2355 10 -23 0.4 1429.87 0.00
0000 10 -18 0.2 1439.73 0.00
0005 10 -25 0.0 1429.84 0.00
0010 10 -17 0.2 1439.73 0.00
0015 0 -33 0.9 1456.33 0.00
0020 10 -12 0.0 1439.73 0.00
0025 1 -33 0.0 1451.72 0.00
0030 10 -12 0.0 1439.73 0.00
0035 10 -26 0.2 1429.83 0.00 DF6NM GN ALL
0040 0 -34 0.4 1440.21 0.00 000AAA 000AAA RA90
I managed to decode your signal
even if it looks like you are slightly out of sync.
https://dl.dropbox.com/u/16381257/capt14.jpg
LA5VNA Steinar
loc:JO59jq
Mal and spam filtering: STRONG
www.opera.no
Den 30.10.2012 11:45, skrev Markus Vester:
Similar here, most (but not all) slots decoded successfully,
but mostly with asterisks. Strange that the quiet slots at odd
ten minute multiples also achieved 10 sync points - perhaps the
echo effect again? The first line went wrong only because my decoder
was still set to 5 minutes.
Even with 1 Hz tolerance the CPU is getting pretty busy - maybe in a future
version we could select whether we want multiple decodes or not? On one of my
machines I can't use 48 kS/s for WSPR and WSJTx because that samplerate is too
far off, so being able to choose between 12 and 48 kS/s aquisition would also
be useful.
Best 73,
Markus (DF6NM)
0040 10 -24 -0.6 1940.53 0.00 000AAA 000AAA RA90
0050 0 -37 0.0 1938.40 0.00
0100 10 -9 1.7 1939.83 0.00 DK7FC JN49IK
0110 10 -18 0.4 1939.83 0.00
0120********* 1.7 1939.83 0.00 DK7FC JN49IK
0130 10 -18 0.4 1939.83 0.00
0140********* 1.7 1939.83 0.00 DK7FC JN49IK
0150 10 -19 0.9 1939.85 0.00
0200********* 1.7 1939.83 0.00 DK7FC JN49IK
0210 10 -17 -1.3 1939.75 0.00
0220 10 -9 2.2 1939.83 0.00
0230 10 -20 0.9 1939.85 0.00
0240********* 1.3 1939.83 0.00 DK7FC JN49IK
0250 10 -17 0.4 1939.83 0.00
0300 10 -9 1.3 1939.83 0.00 DK7FC JN49IK
0310 10 -19 0.4 1939.83 0.00
0320********* 1.3 1939.83 0.00 DK7FC JN49IK
0330 10 -18 0.4 1939.83 0.00
0340********* 1.3 1939.83 0.00 DK7FC JN49IK
0350 10 -18 0.4 1939.83 0.00
0400********* 1.3 1939.83 0.00 DK7FC JN49IK
0410 10 -18 0.4 1939.83 0.00
0420********* 1.3 1939.83 0.00 DK7FC JN49IK
0430 10 -19 0.4 1939.83 0.00
0440********* 1.3 1939.83 0.00 DK7FC JN49IK
0450 10 -19 0.4 1939.83 0.00
0500********* 1.3 1939.83 0.00 DK7FC JN49IK
0510 10 -19 0.4 1939.83 0.00
0520********* 1.3 1939.83 0.00 DK7FC JN49IK
0530 10 -18 0.4 1939.83 0.00
0540********* 1.3 1939.83 0.00 DK7FC JN49IK
0550 10 -18 -1.7 1939.89 0.00
0600 2 -35 0.9 1939.85 0.00
-----Ursprüngliche Mitteilung-----
Von: Terry GW0EZY<[email protected]>
An: rsgb_lf_group<[email protected]>
Verschickt: Di, 30 Okt 2012 2:36 am
Betreff: LF: RE: JT9-10 Decode DK7FC
Decode OK but same again – Sync and dB values shown as **** (usually indicates
values exceed expected)
0120********* 0.9 1138.38 0.00 DK7FC JN49IK
I have reduced the tolerance to +/- 10. I checked JT9-30 and the Wide Graph
scale shifts again requiring another retune and increase of FFT Bins/Pixel to
get 1140 kHz on screen (136.3 + 1140)
73 Terry
From: [email protected]
[mailto:[email protected]] On Behalf Of Terry GW0EZY
Sent: 30 October 2012 01:14
To: [email protected]
Subject: LF: JT9-10 Decode DK7FC
A decode of your JT9-10 transmission. I wonder why the Sync and dB values are
shown as **** ??
0100********* 0.4 1138.38 0.00 DK7FC JN49IK
Waiting for JT9-30 ??
I thought you would prefer to stay with BS – sigh!
73 Terry
From: [email protected] [mailto:[email protected]]
On Behalf Of Stefan Schäfer
Sent: 30 October 2012 00:49
To: [email protected]
Subject: Re: LF: DK7FC-DF6NM
Am 30.10.2012 01:41, schrieb Terry GW0EZY:
Stefan getting regular decodes from you – every 10 minutes. Will also try your
JT9-10. Let us all know if another frequency offset is required.
No, i'll stay at 137.44 kHz over the night.
Sending emails is a pain!
Is it? I like it :-)
73, Stefan
|
