Return to KLUBNL.PL main page

rsgb_lf_group
[Top] [All Lists]

Re: LF: Ublox 8 question

To: LF Group <[email protected]>
Subject: Re: LF: Ublox 8 question
From: Riccardo Zoli <[email protected]>
Date: Fri, 4 Jan 2019 21:27:11 +0100
Dkim-signature: v=1; a=rsa-sha256; c=relaxed/relaxed; d=gmail.com; s=20161025; h=mime-version:references:in-reply-to:from:date:message-id:subject:to; bh=GgN9uDcCSKDeRSpaXJvrNRLPsn9romhW+U2k56ACRB8=; b=YVluN93XV7JBYnheIuELJ+mmCGqD6E9t4qNlW1tJxwt8qxcgMn6qQ1LWLwjvmehhj4 sCEmSH7KsUSETubs8zkTLGRhKzVy56fbCaiPXzQHunzRPrVYAHC1KYJtAdn+GgXbyUH7 n7sUtcyk/FEAISa7xsPg+geSfcoDVRPW+S4e0B0aEmO7hptUC9ZX024Gzqi8q885q/ds 7Dq9aqaDjQGX0bVGD1z6pZa1Iml0fSpFz5Satdg4Hc6yFPlO2jH3B/TH/ZhDRp/bV5hq bD0Z35Sv1RiAxRpfimXjf88sXO8OfHoqyI4fe3+8a9VYrabc9WIW+PXESv01h7v/B/wj 96JQ==
In-reply-to: <[email protected]>
References: <[email protected]> <CANA3B6V=UBmf2hJcxOkH7p1hMuHaTBP3uduy7rL-=kL5Mw1p3Q@mail.gmail.com> <[email protected]>
Reply-to: [email protected]
Sender: [email protected]


Ok, Chris, it's correct to connect the ground probe as near as possible to the module's GND. Please, could you post some pics of your NEO's breakout board?


73 de Riccardo IW4DXW


Il giorno Ven 4 Gen 2019, 20:09 Chris Wilson <[email protected]> ha scritto:


Hello Riccardo,

Thanks, a typo on my phone, I am always doing it, sorry, I was setting
1  MHz  (mega)  :)  I'll try again but that sounds like I was doing it
correctly. Where should the probe ground be taken from please?

Friday, January 4, 2019, 6:21:37 PM, you wrote:



> Hi Chris, LF


> 1 mHz? Maybe 1 MHz: TP frequency must be in the range 0.25 Hz..10 MHz.
> In TP5 settings, toggle frequency and duty cycle flags then set
> 1000000 Hz and 50% d.c. in the f. locked fields. Press "send" button
> (in the lower part of cfg window).




> 73 de Riccardo IW4DXW





> Il giorno Ven 4 Gen 2019, 18:59 Chris Wilson <[email protected]> ha scritto:



>  Hello  LF'ers,

>  My newly arrived Ublox 8 and breakout board has landed and I have had
>  a very quick play with it and the Ublox UCentre software. I have set
>  Time0 to give say a 1 mHz output in UBX / CFG / TP5 but scoping that
>  through hole on the breakout board shows no output. I did instruct it
>  to write to the device, and it sticks. What I am unsure about is where
>  I should be taking the scope ground to, I used the shell of the USB
>  connector socket. i am hoping it's not a fake or knackered... It came
>  from the same place Stefan suggested and is the same model and same
>  break out board he posted. Any idea if it's me being stupid again, and
>  I have overlooked the obvious? Thanks.



>  --
>  Best regards,
>   Chris                          mailto:[email protected]






--
Best regards,
 Chris                            mailto:[email protected]


<Prev in Thread] Current Thread [Next in Thread>