For what it's worth I noticed the same with an older version of
SlowJT9 when I changed the output sound device. The setting did not
take affect until after I closed SlowJT9 and restarted it. It was
not a real problem to me as I only had to do this one time when I
was ready to begin first transmit tests with it.

73,
Paul


On 11/24/18 4:54 AM, Andy Talbot [email protected]
[rsgb_lf_group] wrote:
> After four attempts at starting the software, I managed to get Tune to
> generate audio
> It appears that I have to set the soundcard in the pull down menu then
> close the programme.  When it is then opened again, that soundcard is
> offered as the default.  If left alone it works.
> 
> If I try to select another soundcard, the same procedure is needed;
> settign, close, open, check it is the default offered ...
> 
> It looks as if, at least for audio OUT, you are using the soundcard stored
> in the config file rather than in the pull down menu box
> 
> But I'm pleased to report the catastrophic crash that occurred before when
> no S/C was present has now gone away :-)
> Andy
> www.g4jnt.com
> 
> 
> 
> On Sat, 24 Nov 2018 at 09:45, Andy Talbot <[email protected]> wrote:
> 
>> Rik ...
>>
>> I've just installed 9.11 and am having exactly the same problem with
>> getting audio out.   Either on normal Tx or Tune, no audio is being
>> generated.(Yes, I do have the slider advanced !)
>>
>> Occasionally on 9.10 I did get audio, but it was random as to whether
>> would start or not.  So far even that hasn't happened on 9.11
>>
>> Audio in on Rx is OK
>>
>> Andy
>> www.g4jnt.com
>>
>>
>>
>> On Thu, 22 Nov 2018 at 16:08, Rik Strobbe <[email protected]> wrote:
>>
>>> Dear all,
>>>
>>>
>>> I just uploaded a now beta-release of SlowJT9 (v0.9.11).
>>>
>>> Just some bugs fixed:
>>> - Fatal bug that could cause a crash if the soundcard was not found fixed.
>>> - Non fatal bug that caused wrong audio frequency limitations for JT9.EXE
>>> fixed.
>>> - Non fatal bug that caused a slight timing error fixed. This maybe give
>>> that extra 0.1dB you need to complete the ultimate DX QSO ;-)
>>>
>>> *Be aware that due to the baudrate changes there is NO BACKWARD
>>> COMPATIBILITY for JT9-2 and JT9-5 to version prior to 0.9.10. *
>>> *In other words: JT9-2 and JT9-5 send with v0.9.11 cannot be decoded with
>>> versions v0.9.00 - v0.9.03 and vice versa.*
>>>
>>> The JT9-1 mode however is still the same and can be sent / received with
>>> all versions (and is WSJT-X compatible).
>>>
>>>
>>> *The sole purpose of this version is to determine how JT9-2, and
>>> eventually JT9-5, behave in relation to the previous versions, so we can
>>> decide wether SlowJT9 will proceed with the original parameters (anno
>>> 2013) that imply an odd baudrate ratio between the JT9 submodes or my
>>> previous parameters, with "round number" ratios. *
>>>
>>> *Therefore all test reports, remarks, suggestions and opinions are most
>>> welcome.*
>>>
>>> For the same reason no other changes are applied.
>>>
>>>
>>> I want to thank everybody who gave feedback, suggestions and bug reports
>>> over the past weeks, this was very much appreciated!
>>>
>>>
>>> Whoever is interested can download the SlowJT9 installation file at
>>> http://472khz.org/SlowJT9/SlowJT9_setup.exe.
>>>
>>>
>>> For now only a Windows version of SlowJT9 is available. But as the used
>>> IDE has cross platform facilities it should be possible to support other
>>> operating systems as well in the future.
>>>
>>> 73, Rik  ON7YD - OR7T
>>>
>>>
>>>
>>>
>>>
>>>
>>>
> 

-- 
Paul
N1BUG  2200m-2m        DXCC Honor Roll
FN55mf      ME      Piscataquis County
http://www.n1bug.com
http://www.aurorasentry.com