It had to really wonderful, Eddie!
No, this carrier was not me. If I am going to transmit, I will let
it know.
73!
Lubos
*******************************
Dne 5.4.2011 11:35, qrss napsal(a):
Hi Lubos
That chimney sounds wonderful, it reminds me of some superb Top
Band signals using Works QTH chimneys for antenna support, many
years ago.
Did you run your TX last night around 20.00UTC a strong carrier
was seen here and on EU Grabbers on your frequency.
73 Eddie G3ZJO
On 05/04/2011 09:53, Lubos OK2BVG wrote:
Hello Stefan!
You are right, I would like to see your VLF DFCW-3 signal
again ![Veselý obličej]( "Veselý obličej") .
As for my plans ... I will have to find out more better
QTH for transmission. There is lots of as high as my antenna
hight buildings around my QTH here. I am sure, it decrease
its ERP significantly. If I have more better TX QTH, than
I will can think about increase my power from 120W to ???W.
There is old factory near my QTH. I discussed with the
director about using a high factory chimney for my VFL
purposes. I am waiting for his answer. It is half to half.
73!
Lubos, OK2BVG
Date: Mon, 4 Apr 2011 23:11:04 +0200
From: [email protected]
To: [email protected]
Subject: Re: LF: OK2BVG-DK7FC
Hello Lubos,
Am 04.04.2011 19:20, schrieb Lubos OK2BVG:
I hope to see your signal soon. I built a new
modification of your VLF active antenna, so it would be
the good opportunity for testing this one.
But for test purposes it is better to have a weak signal, just
above the noise ;-) But i know you are monitoring in DFCW-3...
So, what do you plan next Lubos? QRO to 500 W? This would
allow you to produce a signal visible in TF i think. And you
will be visible in even worse conds. Or your signal will be
visible during the night period which allows you to send a
full callsign or such funny things ;-) Any plans?
73, Stefan
73!
Lubos, OK2BVG
Date: Mon, 4 Apr 2011 16:03:06
+0200
From: [email protected]
To: [email protected]
Subject: LF: OK2BVG-DK7FC
Text zprávy
Hello Lubos,
Congratulations! This is your first clear trace on my
grabber in 6000 / 424 uHz. First i thought it is OE5ODL
but there is no trace on his grabber but a strong trace on
OE3GHBs grabber. And if you are sure about the TX
frequency, it must be your signal. Very fine, 600 km ( http://no.nonsense.ee/qthmap/?qth=JN49IK&from=jn88ks
), my first OK RX contact :-)
Best 73 and QRO ;-)
Stefan/DK7FC
PS: Maybe we can have a "K" now once again? It is a better
ID than a long dash...
Am 04.04.2011 13:49, schrieb Lubos OK2BVG:
Hello Eddie!
It would be my signal. We will see, but it seems to be
promissing!
The conditions are good, so I will transmit until
12:00UT.
My PC is disciplined by WaG generator PS30 (10kHz). See
my signal on the Stefan´s grabber in DFCW6000 window.
The frequency is correct: 8970.034Hz
My new PA 120W running on its full power. It is doing
its best :-) !
73!
Lubos, OK2BVG
Date: Mon, 4 Apr 2011 11:30:17
+0100
From: [email protected]
To: [email protected]
Subject: Re: LF: 110404_OK2BVG
Hi Lubos
I am pretty sure we have here. I make your frequency
8.970034kHz. We will not get excited yet :-)
How stable is your signal, it seems possibly not stable
enough for QRSS 60000 to help.
Continued operation after 11.00 UTC would help
identification.
73 Eddie G3ZJO
On 03/04/2011 20:32, Lubos OK2BVG wrote:
Hello
OMs!
I
will be testing my VLF PA 120W tomorrow:
Date: 04.04.2011
Time: 07:00 UT -
11:00 UT
Antenna: Marconi L
24m up + 220m top load
PA: 120W
Identification: long carrier only
Mode:
FRQ: 8970.040
(+/- some few mHz :-)
Shift:
I
hope, the conditions will be good :-)
73!
Lubos,
OK2BVG
|
|
