Return to KLUBNL.PL main page

rsgb_lf_group
[Top] [All Lists]

LF: AW: 4th VLF experiment by DK7FC/p

To: <[email protected]>
Subject: LF: AW: 4th VLF experiment by DK7FC/p
From: "Beckmann, Gerhard" <[email protected]>
Date: Fri, 2 Apr 2010 21:38:12 +0200
In-reply-to: <38A51B74B884D74083D7950AD0DD85E82A1BBF@File-Server-HST.hst.e-technik.tu-darmstadt.de>
References: <[email protected]><001d01cad190$aa92e590$0901a8c0@lark><841031C22EC944FEB2BB3E1DC237717E@acer3f31164f8b> <[email protected]> <38A51B74B884D74083D7950AD0DD85E82A1BBF@File-Server-HST.hst.e-technik.tu-darmstadt.de>
Reply-to: [email protected]
Sender: [email protected]
Thread-index: AcrR1mvShwr635oISpWIskYmRncGfAAIcCAfACjCYoA=
Hello Stefan,

 

I also will try again to catch you on my screen tomorrow morning. 

Alpha beacon is coming with 25 dB.

Good luck for the new VLF experiment !!!!!

 

vy 73 de Gerhard  //  DK6NI

 

 

=======

 

 

 

 

  _____  

Von: [email protected]
[mailto:[email protected]] Im Auftrag von Stefan Schäfer
Gesendet: Freitag, 2. April 2010 02:39
An: [email protected]
Betreff: VLF: 4th VLF experiment by DK7FC/p

 

Dear group, 

After a break of one week i plan to transmit again on VLF / 8,97 kHz. If the
wind will be enough i will come up on saturday, 3. April, at arround 10 UTC.

The DFCW-600 mode was a good choice in the last experiment, so i will keep
this mode. 

If Markus/DF6NM has time to make QSP on the mobile phone to the reflector
(Markus ?) we could arrange various tests. I will also call other local
stations for reception reports during the transmission.

There will be some new components to test: 

Today i started building up the 600W class D PA (at least 600W) that is
directly fed out of the 230V (rectified) of the generator. PTT and VFO input
is realised by fiber optic cables. The DC capacitor is 2000µF/350V and can
be put on voltage without a NTC or charging resistor due to the relatively
high output impedance of the small generator (tested). This works very fine
now. Tomorrow i will apply the FETs and the big ferrite core and it's
windings. Then i will do a test on a dummy load at home. If the signal will
be 3dB stronger, we could theoretically change to DFCW-300 compared to the
last experiment. But there are many OMs writing private mails to me and
prepare to be QRV on this next test. Some of them are using E-Field antennas
and/or are more than 860km away, that' why i want to stay in QRSS-600 first.
So there might come a new distance record? In any case it will be exciting
to me watching the new system running :-) Also it will be interesting to see
if the E-field antenna will get the signal!

The primary winding of the TX coil is increased from 9 to 13 turns due to
the higher power that will be applied. Otherwise the current will become to
high.

I will mount the amperemeter (analog, 1A) into the coil. That makes it
easier to adjust to resonance and watch the stability and maximum and
average (estimation) current.

Finally i will try to apply some copper rods into the earth and will look
how the antenna current is changing.

The goal is to radiate 4mW ERP. Another goal is to reach as many stations as
possible. So i would be pleased if YOU would be one of them. :-)

Since the QRM/QRN comes up in the late afternoon and transmitting for 4...5
hours i will close at about 15 UTC. So the planned LF activity is not
affected :-). Sorry, but i cannot participate on the LF acty later since the
VLF coil takes all the place in my car ;-)

I looking forward to this experiment and wish you good luck and fun by
receiving  :-)

73 es gl, Stefan/DK7FC

PS: Could you give me a short feedback if you plan to be RX?

 

<<attachment: winmail.dat>>

<Prev in Thread] Current Thread [Next in Thread>