Dear all. 1515 utc I have just worked Wolf DF0WD with 100% copy using Jason both ways. Wolf was running 50W and I was running 150W. Wolf's signals were audible here but a heavy noise level would have
Thanks Brian. That seemed to by my half of the QSO and also my first reception report from CT! 73. Dave G3YXM. Part of QSO received in CT and am now putting it on my web pages. 73, Brian At 14:39 16/
Additional note: Jason 0.91 works fine on my P100 laptop, it's a really crappy Compaq so any decent machine should be OK. It doesn't seem an awful lot slower either. Well. done Alberto. Dave Yes I wi
Alberto and all. Yes I will transmit for one hour from 2000 utc on 137.520 using Jason 0.91 in "Slow" mode. I have put the software on my web-site in case QSL.net is too busy. http://www.wireless.org
Thanks to all who sent reports by e-mail or telephone. It seems you have a winner here Alberto! I was especially pleased you managed to copy it so well. TX power was about 150W output. Jason was gene
Yes, centre frequency should correspond to 137.520 but as I said earlier the IC735 does drift slowly so may be a few Hz out. It was exactly right at 1500. Dave G3YXM Dave, I think that your transmiss
Alan / Alberto. Sounds like the same problem I had, what speed is your processor? I have now had good decode of a locally generated weak signal that would have been "M" copy on 3sec QRSS and was deco
Uwe and Alan. I don't know how often you get mail but I will transmit at 1500 for 30minutes (if my cheapo PSU will stand it!) and then listen. I will get as close to 137.520 as I can, my old IC735 TX
Thanks Alberto. I tried the 850MHz P3 laptop and it works fine. Obviously the 200MHz machine is not good enough, I will have to upgrade the shack computer :-( I made a very weak signal and listened t
Alberto. I have the whole shack in turmoil with wires all over the place trying to make Jason work across the room. I am using sound-card TX mode as I have an SSB exciter on 136 kHz so I can transmit
Fabian. Please try again if you hear (see) me. I would have been able to copy if the noise had stayed away. You also had a slight drift which took you across a Loran line which didn't help! 73. Dave
Hello Geri. I saw you on DFCW today but with Argo set for 3 sec dots, your shift was too small to read easily. My slow PC will not go fast enough to read it any other way! Who was the "1YFK" (I think
Steve. I think there was some confusion as to whether you were the wobbler or the wobblee... Ah, yes that could be misconstrued but do I really have to resort to those "emoticon" things? What exactly
Mal et al. I have "The Matrix" on my web-site, it doesn't cater for 1-ways and I've not added many cross-bands but it's supposed to be a record of the first QSO between each pair of countries. If any
Andy The low power TX?? I didn't see anything of it during the evening. Perhaps it was someone else then... it was strength 7 here, not bad for 4 Watts! Dave. Sorry, its only the low power Tx. Variou
Is that Andy with a full power data transmission in the middle of the CW area..... on a Sunday? Someone might go off in huff if this carries on! Dave G3YXM.
Mal. It's PNP silicon, VCEmax=100V, ICmax=8A, Diss 80W, Ft=4MHz, HFe 1000 (must be a darlington) equiv to BD652 says Towers. If you place the device heat-transferring surface downward, with the legs
Valerio, John, Laurie etc. I have just checked my calibration against Rugby and I reckon I can be pretty accurately on 9225 Very impressed that the signal stayed in 'till 0900, I pulled the plug abou
Dear all. There are several signals on tonight, I think Laurie is on .9215 and I'm on .9225 but only slight traces are visible on John's screen grabs so things aren't looking good so far. It's a grea
