Return to KLUBNL.PL main page

rsgb_lf_group
[Top] [All Lists]

Re: LF: MSK with a Class D transmitter...?

To: [email protected]
Subject: Re: LF: MSK with a Class D transmitter...?
From: Andy Talbot <[email protected]>
Date: Thu, 21 Apr 2011 18:51:53 +0100
Dkim-signature: v=1; a=rsa-sha256; c=relaxed/relaxed; d=gmail.com; s=gamma; h=domainkey-signature:mime-version:in-reply-to:references:date :message-id:subject:from:to:content-type; bh=odYXLip7WrNq/WdoA9sGbcKZGe/PjuCtK+Gy0pev7tw=; b=ANoiuyZsbSuDElCCofzNJgf0V7Wdv/5+CSL87ErZViapuPFF5z5emaBkIud3iUbc+/ D/pCrx24lvD5fzU/viRWNQ7YygaAitrovttDahOtO3HtDGflVEMbpvXblu9LPtSiyKG2 VAKv/vDI9VoeeDru6K1jEuNzTjqxv+7kxdyNM=
Domainkey-signature: a=rsa-sha1; c=nofws; d=gmail.com; s=gamma; h=mime-version:in-reply-to:references:date:message-id:subject:from:to :content-type; b=L2HzyomRNKPLXAANQc5KCA0qGllUquqzg1WE/gjXwL4sLnMOyIrCQwzm87flOig3IH vq4nFOnhWb4hnPeruMaOStNPMjeXjUfKKIZMnTBo+R8yB25dPsGftWGWAyBqXz/gLG2G SJQxhLCgX48VoTdkiRaDMelDqEckZdYay32g8=
Domainkey-status: good (testing)
In-reply-to: <BF4A524700075746A6467658DFC7102C88B4A788BD@ICTS-S-EXC2-CA.luna.kuleuven.be>
References: <[email protected]> <[email protected]> <[email protected]> <[email protected]> <[email protected]> <BF4A524700075746A6467658DFC7102C88B4A788BD@ICTS-S-EXC2-CA.luna.kuleuven.be>
Reply-to: [email protected]
Sender: [email protected]
WSPR isn't MSK..  (Minimum Shift Keying)
Its MFSK   (Multi Frequency Shift Keying)
 
'jnt


 
On 21 April 2011 18:46, Rik Strobbe <[email protected]> wrote:
Hello Scott,

 

what kind of MSK do you want to transmit ?

WSPR by any chance ?

 

73, Rik  ON7YD - OR7T


 
On 21 April 2011 01:28, Scott Tilley <[email protected]> wrote:
Hi Andy

Holy mind bogglingness batman...

Here's the parameters to make this real simple:
- I want to generate a MSK signal out of the transmitter at 8970Hz.
- I'm using Spectrum Lab, which allows me to create a MSK drive and at a baud rate I want at any frequency my sound card can generate.
- SL allows me to output quadrature outputs.

So, If I understand correctly pump said FET driver with the quadrature outputs from the sound card audio (squaring up the sine waves of course) and it should work?

Thanks,
Scott






On 4/20/2011 2:09 PM, Andy Talbot wrote:
Bin too quick to type..
NOt thinking straight...
 
You need to the upconvert either the resulting doubled audio tone by twice the RF carrier, or upconvert first and double the final RF.  Same ideas for frequency doubling can be used.
 
See http://www.g4jnt.com/LFUpconv.pdf  for a direct from audio upconverter.
 
Must fully check before hitting SEND !
 
Andy
G4JNT

On 20 April 2011 21:50, Andy Talbot <[email protected]> wrote:
I assume you are genrating the MSK from soundcard output, in which case two options come to mind:
 
1)  Double the frequency.  Full wave rectify the audio sinusoid, pass the AC part of the result into a comparator and into the divider.  Alternatively, as the signal bandwidth is probably quite low, square up the audio to start with, feed into one inpiut of an XOR gate.  Delay the waveform by 90 deg and feed this into the othe side of the XOR.    Output of XOR to divider as before
 
2)   Remove the  divide by two, and replace with an inverter / buffer pair to generate the out of phase drive signals.   The  input now needs to be close to a 1:1 squarwave at output frequency.   Pass the soundcard audio into a comparator and make sure it gives a 50% duty cycles.
 
 
Andy
 
ps.
or 3)    Convince the software author the S/W needs modifying to give a 2.F output
 
 
On 20 April 2011 21:32, Scott Tilley <[email protected]> wrote:
Hi All

I wonder if someone can explain to me how to feed an MSK signal into a typical Class D transmitter?

I mean by typical that the TX has a 4013 type /2 system feeding two FET drivers to drive FETs in a push-pull configuration.

If I understand correctly due to the fact MSK does not have amplitude component to its signal that a non-linear transmitter can be used.

So, how do you do this with a Class-D TX as often used in LF/VLF?

Thanks,
Scott
VE7TIL








<Prev in Thread] Current Thread [Next in Thread>