Hi G., Am 22.09.2012 22:54, schrieb Graham: Stefan If you can generate the signal of your previous tests , I don't think the range will be that short !! Ooh, what was my previous test? I've done seve
Happy days are here again .. and my local MW station is still qrt Smile emoticon Smile emoticon Yes , ref , your 8K test's some time ago , I remember you reached TH3 ?? , Gary also had a trace from y
Hi Steinar, I can see the center frequency of Soundoutput is 2000 Hz. The default center frequency of WSPR is 1500 Hz though. Did you edit the wspr-32rx.bat file and set the values of fc correctly? I
LF! I just prepared the new set of files and successfully transmitted the normal WSPR-2. Got decodes from the active RX stations. So this is working at least. Now i set up for WSPR-8 and will run a b
I'll give it a try Graham. The problem may be to find monitoring stations in a short range... 73, Stefan Am 22.09.2012 17:20, schrieb Graham: And of course there is a 240 SDR data mode , all ready fo
Hello Terry, Very good! Thank you for the efforts. It looks like YO/4X1RF has managed to set up the WSPR-8 system as well, and got decodes from DF6NM/8 and DK7FC/8. So, so far there is DF6NM DK7FC GW
Hi Terry, it looks like the frequencies don't match yet. SndInput fc should be the incoming audio band from the RX, and SndOutput fc should correspond to the BFO frequency in WSPR. The fc value can b
For those interested, the slowWSPR utilities can be downloaded at http://df6nm.bplaced.net/wspr/slowWSPR.zip (97 kB) There is a readme file which will hopefully give you an idea of how to proceed. Bu
And of course there is a 240 SDR data mode , all ready for 8Khz tested to -50 dB as bench mark : ) From: Stefan Schäfer Sent: Saturday, September 22, 2012 1:57 PM To: [email protected] Sub
Hi Markus Thanks for the advice – modified s/w in use. I have copied you both but spots are not being uploaded to WSPRnet – the upload box is checked and it is normally OK. 1608 -6 0.8 0.
Stefan If you can generate the signal of your previous tests , I don't think the range will be that short !! Due to the long tx pulses of OP4 Hr , the signal will also show on spec-lab , so test data
Hi Stefan, sorry, only just started the RX before 7 UT. So here's your decode, delayed by 10 minutes... 2012-09-22 07:10 DK7FC 0.137429 +12 0 JN49ik 1 DF6NM/8 JN59nj 175 91 The offset was shown as DT
Hi Steinar, I can see the center frequency of Soundoutput is 2000 Hz. The default center frequency of WSPR is 1500 Hz. Did you edit the wspr-32rx.bat file and set the values of fc correctly? If WSPR-
Terry, wow, excellent! Thanks very much for your patience. Best 73, Markus From: [email protected] Terry GW0EZY Sent: Saturday, September 22, 2012 6:27 PM To: [email protected] rsgb_lf_group@
Hi Marcus I can never resist the opportunity to play with new software decoders!! I have tried to set up the software according to the readme file but no success so far. A folder has been setup with
Stefan I am not able to get a signal into the waterfall with wspr-32 :( With wspr-8 the signal was visible. https://dl.dropbox.com/u/16381257/Clipboard01.jpg la5vna S
Hi all, Hmmm, theoretically we can generate every WSPR speed now. Markus, should we try a WSPR-256 on VLF/ 8970 Hz? :-) I still have the big coil in the cellar and the band looks fine :-) Remember th