Return to KLUBNL.PL main page

rsgb_lf_group
[Top] [All Lists]

Re: LF: Experimental software for WSPR-8 and -32

To: <[email protected]>
Subject: Re: LF: Experimental software for WSPR-8 and -32
From: "Markus Vester" <[email protected]>
Date: Sat, 22 Sep 2012 13:27:36 +0200
Cc: <[email protected]>
Dkim-signature: v=1; a=rsa-sha256; c=relaxed/relaxed; d=mx.aol.com; s=20110426; t=1348313261; bh=Ka835Vl8XLhOrKHL9HrJsY1kVNeBAeXGskdxclis2tQ=; h=From:To:Subject:Message-ID:Date:MIME-Version:Content-Type; b=Tl5e+sPv+iEdBgTKneFu/b/f4M8XRabVQZZoqyZD/QICGXzG519/JyEiLQmGzgHB7 KNxUadIa9PP0D3AYHyVuGwGy1gnzTDY45PRUX4VnSYARR7q5mK0e0Jq8igrYTvD8mJ 9JCLc1hdN6UYAmVcO/9l5eazP60H5fQ+3kMEyD7c=
Importance: Normal
References: <41E179E8BC3D497AB344D966959A61C6@White> <[email protected]> <386BA5055A494FEC9164314A593DCB8D@White> <000901cd98a8$7cd20a00$76761e00$@com>
Reply-to: [email protected]
Sender: [email protected]
Hi Terry,
 
it looks like the frequencies don't match yet. SndInput fc should be the incoming audio band from the RX, and SndOutput fc should correspond to the BFO frequency in WSPR. The fc value can be edited in the little SndInput / SndOutput windows so you won't have to restart the batch script. 
 
Stefan and I are currently sending WSPR-8 on 137430 / 137440 Hz in alternate 10 minute slots. Thus with your 136 kHz LO, you could set fc = 1430 in SndInput. As your WSPR is listening around 2 kHz, SndOutpt needs to have fc = 2000. If you would like to show the correct frequency for Stefan in the spots, you can set the dial entry in WSPR (but not your RX!) to 0.13543 MHz.
 
BTW I have uploaded a modified version today which starts the replay immediately after the incoming signal has ended. So the spots will be delayed by 8 instead of 10 minutes. There are also some amendmends in the readme.
 
Good luck,
Markus (DF6NM)
 

Sent: Saturday, September 22, 2012 11:56 AM
Subject: RE: LF: Experimental software for WSPR-8 and -32

Hi Marcus

 

I can never resist the opportunity to play with new software decoders!!

 

I have tried to set up the software according to the readme file but no success so far.

 

A folder has been setup with all the files from your zip + sndutl_e.zip

 

I am using an SDR14,  VAC 4.12,  Win7/32, WSPR2.11

 

The VAC is set as default Soundcard for recording and output. The SDR14 (dial or reference frequency = 136 kHz)  is set to use VAC for output. WSPR is set for VAC as input.

 

I have set WSPR with BFO=670 Hz.

 

After running wspr-08_rx.bat

 

The Sound Input panel shows  fr/Hz = 670 (autoset); ft/Hz = 0 ; bu = 100% vo = 0%

 

The Sound Output panel shows fc/Hz = 2000;  ft/Hz = 0; bu = 0%

 

The DOS CMD panel shows some sort of loop action: copy audio.dat audio2.dat 1 file copied; goto loop; waitraster 600 -20; del audio.dat; waitraster -120 -5 etc etc

 

However WSPR is not seeing any signal input.

 

Where is my mistake in setting up??

 

73 Terry

 

<Prev in Thread] Current Thread [Next in Thread>