Return to KLUBNL.PL main page

rsgb_lf_group
[Top] [All Lists]

Re: LF: 137 ck

To: <[email protected]>
Subject: Re: LF: 137 ck
From: "mal hamilton" <[email protected]>
Date: Tue, 9 Aug 2011 16:57:26 +0100
References: <001901cc55f1$52b9f660$0401a8c0@xphd97xgq27nyf><CAJStiw5zh_bUWj0MfOz57pvN0yo7g5cxVK4fRi9znSXOfWU1Vg@mail.gmail.com><003701cc55f8$e9e01950$0401a8c0@xphd97xgq27nyf> <CAJStiw53-YWAg15U89fxvwVCO4OKn+wn2MeBzrcQHkgCB9nPLw@mail.gmail.com> <006801cc5601$705d4ae0$0401a8c0@xphd97xgq27nyf> <2CCA2BE4259248B4ABDC241F0EE58FA8@AGB>
Reply-to: [email protected]
Sender: [email protected]
Graham
The display looks clean this end also the audio sounds pure with no 100 hz hum as monitored on an independent RX
I have the proper C's es L for decouping as per Decca instructions with this TX.
With a strong signal on some Grabbers there will be the dog bone effect with leading/trailing edge blips from keying carrier on/off
but on scope no transients visible.
73 de mal/g3kev
 
----- Original Message -----
From: Graham
Sent: Monday, August 08, 2011 11:49 PM
Subject: Re: LF: 137 ck

That's  the problem  with  modern   digital  technology , the  dynamic range  exceeds , that  of the  MK-1   eye  ball , 30 db is  1000:1  , will  show at  20 db over the  noise and  would  not  show on the  scope
 
Use a  reasonable   decoupling   capacitor  , and look at the  psu   voltage  using  a  (cheap) sound  card  (with high z resistive ladder for  safety) ..use  Wolf's   SPEC-LAB   to   view  the dB  attenuation  at  50, 100, 150 , 200  Hz  etc
 
Depending  on the  loop  bandwidth  of the  stabiliser , keying  may  also  induce  transits  , use the  peak  hold to  observe the  generated  spectrum
 
G..

Sent: Monday, August 08, 2011 8:29 PM
Subject: Re: LF: 137 ck

No hum Gary
I am monitoring on the scope and sig is vy clean
mal/g3kev
 
----- Original Message -----
Sent: Monday, August 08, 2011 8:19 PM
Subject: Re: LF: 137 ck

OK Mal,

Captures are at 10 minute intervals, but I have saved you going to SpecSavers as I have enlarged the frequency readout.

BTW...do you have some 100Hz hum on your transmission, look at my grabber to check.

73

Gary - G4WGT.


On 8 August 2011 19:28, mal hamilton <[email protected]> wrote:
Yes Gary
Your grabber seems to have a long delay before display es the times and freq hard to read
otherwise sensitivity seems ok at present for distance
73 de mal/g3kev
 
----- Original Message -----
Sent: Monday, August 08, 2011 7:21 PM
Subject: Re: LF: 137 ck

Mal,

You wrote.........While testing earlier find NO UK GRABBERS working

My 500kHz & 137kHz grabber runs 24/7....


Gary - G4WGT.


On 8 August 2011 18:33, mal hamilton <[email protected]> wrote:
Just finished my new PSU 60V/10A psu. While testing earlier find NO UK GRABBERS working and DK7FC has a SPURIOUS wobble signal right on 137.7
I will be QRV for a while from now on 137.7 qrs3 for DX qso's and will work locals on CW
73 De Mal/G3KEV
 




<Prev in Thread] Current Thread [Next in Thread>