Graham, that's what I have so far: RX1: 15:05 @ 2,1 Hz: SQ DE G0NBD P[*2![?LJA& <STOP> -33 dB RX1: 15:28 @ 2,1 Hz: 7Q D?M+!K H <CANCEL> -35 dB RX1: 16:43 @ 2,1 Hz: ^W-!V7G1T13GI= <CANCEL> -35 dB RX1:
Rik, LF, I have to QRT now, I will continue tomorrow night & try faster modes. Thanks for your comments. 73, Gary - G4WGT. On 28 August 2010 21:40, Rik Strobbe <[email protected]> wrote: Ga
Thanks Rik That is useful ! .. will leave it running for a while I was not sure if the 'repairs' to the Ae had reduced the efficiency , as I used to be able to decode via the delft web-sdr ,in the da
Graham, good copy since 18UTC : RX1: 18:00 @ 2,1 Hz: CQ DE G0NBD IN IO83LK <STOP> -34 dB 594 km @ 300º RX1: 18:07 @ 2,1 Hz: CQ DE G0NBD IN IO83LK <STOP> -32 dB 594 km @ 300º RX1: 18:13 @ 2,1 Hz: CQ D
Graham Nice QRO station, good copy, show the QRP merchants how it should be done. g3kev -- Original Message -- From: [email protected] Graham To: [email protected] rsgb_lf_group@blac
Gary, I had a good visual signal, but no decode. I'll try to figure out what is wrong. 73, Rik ON7YD - OR7T Van: [email protected] [[email protected]] namens Gary -
Graham Nice QRO station, good copy, show the QRP merchants how it should be done. g3kev -- Original Message -- From: [email protected] Graham To: [email protected] rsgb_lf_group@b
Not just you, Rik - me too, and I guess some others, probably! Tell us how to do it when you find out. Martin GW3UCJ. I had a good visual signal, but no decode. I'll try to figure out what is wrong.
Thanks Rik That is useful ! .. will leave it running for a while I was not sure if the 'repairs' to the Ae had reduced the efficiency , as I used to be able to decode via the delft web-sd
G.. Could be a problem with the sound card when I tried to run the two modes , , cmsk lock's to 8KHz and ROS needs 48Khz , result was , ros did not decode after the initial frame lock .. may of chang
Gary, I just installed the new beta version of CMSK and it comes up with a default audio frequency of 1000Hz. Is that OK for 502.3 USB dial (thus listening on 503.3kHz) ? 73, Rik ON7YD Van: o
Rik, Go to top menu & select <Tx Options> then <Tx Fequency> & set to 1500. Gary, I just installed the new beta version of CMSK and it comes up with a default audio frequency of 1000Hz. Is that OK
Graham: RX1: 19:15 @ 2,1 Hz: CQ DE G0NBD IN IO83LK <STOP> -27 dB 594 km @ 300º RX1: 19:22 @ 2,1 Hz: CQ DE G0NBD IN IO83LK <STOP> -30 dB 594 km @ 300º RX1: 19:29 @ 2,1 Hz: CQ DE G0NBD IN IO83LK <STOP>
Gary, I just installed the new beta version of CMSK and it comes up with a default audio frequency of 1000Hz. Is that OK for 502.3 USB dial (thus listening on 503.3kHz) ? 73, Rik ON7YD Van: owner-rsg
Graham, just had this copy while ROS and CMSK software were running simultanious: RX1: 16:55 @ 2,1 Hz: CQ,,E G0NBD IN IO83LK <STOP> -35 dB 594 km @ 300º 73, Rik ON7YD - OR7T Van: owner-rsgb_lf_group@
Rik, Looks like I need another 3dB for 100% decode ! fb on the sound card .. may be a change , that was the same problem with wspr , sample rate not locked . Q have you only 2 decodes ? tnx - G.. Fro
Power 110 watts rx 502 khz usb -onbeacon in auto report mode tx mf-1 Rpt welcome , G . From: [email protected] Graham Sent: Saturday, August 28, 2010 3:00 PM To: [email protected] Su
Gary, yet another good visual signal but no decode. It seems to me that CMSK8 is very hard to tune. As you signal is strong (in fact stronger than Gary) it might be worth trying CMSK63, what should b
Gary, I just installed the new beta version of CMSK and it comes up with a default audio frequency of 1000Hz. Is that OK for 502.3 USB dial (thus listening on 503.3kHz) ? 73, Rik ON7YD Van: o