Return to KLUBNL.PL main page

rsgb_lf_group
[Top] [All Lists]

RE: LF: ros -MF 502 K -on now-

To: "[email protected]" <[email protected]>
Subject: RE: LF: ros -MF 502 K -on now-
From: Rik Strobbe <[email protected]>
Date: Sat, 28 Aug 2010 22:32:34 +0200
Accept-language: nl-NL, nl-BE
Acceptlanguage: nl-NL, nl-BE
In-reply-to: <BF4A524700075746A6467658DFC7102C63821D3C83@ICTS-S-EXC2-CA.luna.kuleuven.be>
References: <1741DFA12A93497498225EEE675D5806@AGB> <6392A70598D241C9AC1D1866781D77EE@AGB> <1A65325BA9324EFFA87C0119552B2B48@AGB> <009d01cb46da$38fcfd70$0401a8c0@xphd97xgq27nyf>,<[email protected]>,<BF4A524700075746A6467658DFC7102C63821D3C83@ICTS-S-EXC2-CA.luna.kuleuven.be>
Reply-to: [email protected]
Sender: [email protected]
Thread-index: ActG5lPXHr2YLOqMQeeBdj5tYQHaGQACJ5mmAABM2eU=
Thread-topic: LF: ros -MF 502 K -on now-
Gary,
 
yet another good visual signal but no decode.
It seems to me that CMSK8 is very hard to tune.
As you signal is strong (in fact stronger than Gary) it might be worth trying CMSK63, what should be less critical for RX tuning.
 
73, Rik
 

Van: [email protected] [[email protected]] namens Rik Strobbe [[email protected]]
Verzonden: zaterdag 28 augustus 2010 22:23
Aan: [email protected]
Onderwerp: RE: LF: ros -MF 502 K -on now-

Gary,
 
I had a good visual signal, but no decode. I'll try to figure out what is wrong.
 
73, Rik  ON7YD - OR7T
 

Van: [email protected] [[email protected]] namens Gary - G4WGT [[email protected]]
Verzonden: zaterdag 28 augustus 2010 21:15
Aan: [email protected]
Onderwerp: Re: LF: ros -MF 502 K -on now-

OK LF,

Ready to run CMSK8 again at 100mW ERP.

502kHz USB dial freq Tx at 1500Hz.

73

Gary - G4WGT.



On 28 August 2010 18:55, mal hamilton <[email protected]> wrote:
Graham
Nice QRO station, good copy, show the QRP merchants how it should be done.
g3kev
 
----- Original Message -----
From: Graham
Sent: Saturday, August 28, 2010 5:37 PM
Subject: Re: LF: ros -MF 502 K -on now-

Power  110 watts
rx  502 khz usb -on-
beacon in auto report mode
tx mf-1
 
Rpt welcome , G .

From: Graham
Sent: Saturday, August 28, 2010 3:00 PM
Subject: Re: LF: ros -MF 502 K -on now-

couple of glitches
 
back  at 1457 local  100 watts mf-1
 
rx  502 usb  -ON-

From: Graham
Sent: Saturday, August 28, 2010 12:42 PM
Subject: LF: ros -MF 502 K -on now-

Running  ROS -MF-1 beacon
tx/rx 502 K usb
rx - 502 K
beacon in auto  reply  
 
50 watts  to Ae
 
tnx Gary  for auto  spot







<Prev in Thread] Current Thread [Next in Thread>