Hello all LF's. Where has every one gone on 500kHz, I listen most days at 11.00 UTC and put out a call but I never hear anyone. Regards. Ken M0KHW IO91TV
Hello all. I need an Rx sensitivity and TX frequency check on 500kHz, if thre is any one not far form Luton who can help please mail me so we can arrange a sked. 73 Ken M0KHW IO91TV
Hello John. Thanks for the reply, the receive problem has only just started, I have been working 500 for several months with no problems, working into europe. Just recently I have not been having any
Hello John. Thanks for your report, it looks as if my 90mW is reaching you ok, on the receive side I could not hear any signal on the band with or without the RX pre-amp in circuit. So will still nee
Hello all. Sorry if I have not replied to every one to answered my request, I tried to open them on the shack pc and it deleted them for some reason so I do know who replied. I would be grateful if y
Hi Dennis. Just send me an email and we can arrange a time. 73 Ken M0KHW -- Original Message -- From: [email protected] DENNIS EASTERLING To: [email protected] rsgb_lf_group
Hi Dennis. Sorry i did not reply to your email, I thought I had done so, I have not been very active on any band for the last month, decorating etc. Next week 'should' be a little easier for me, stil
Dear all. I think Laurie has come up with a very good idea,also possibly a weekend slot(s). If I knew there was a good chance of a QSO then I would come on more often, it would need to be no fancy tr
Hi Laurie Try Vincent at IQ Electronic Design Tel: 020 83910545, email [email protected] I have had very good results from Vincent in the past. 73 Ken M0KHW -- Original Message -- From: lau
Dear all. I am still active in Luton, locator IO91TV, on 500kHz running 100mW ERP. 73 Ken M0KHW -- Original Message -- From: "Richard Newstead" <[email protected]> To: <[email protected]
Hi Andy. Where can I obtain a copy of Ansoft Designer from, I usually use Addie for filters, a second option would be worth having. 73 Ken M0KHW -- Original Message -- From: [email protected]
Hello Jim. I could just about hear you in Luton, IO91TV , at 19.50 UTC 73 Ken M0KHW -- Original Message -- From: "James Moritz" <[email protected]> To: <[email protected]> Sent:
Hi everyone, I thought this may be of interest, it came from one of my Total Solar Eclipse sites. 73 Ken M0KHW -- Original Message -- From: "Anthony Ayiomamitis" <[email protected]> To: "Solar Eclip
Hello everyone. Does any one have experience in using microwave oven transformers in high voltage power units, I acquired two of these at the weekend. I was informed that as they stand the voltage re
Hi. Not sure what they do, this was info from the person who sold them to me, he seemed to know a lot about themand using them in PSUs. Maybe someone in this forum can write a short explanation for u
Jim. There will probably be a fair bit of technical smoke comimg out of Luton, but that is what our hobby is all about, any other usefull sugestions? Krgards. Ken 73deM0KHW -- Original Message -- Fro
Hi Pete. I only have one antenna at pressent, so unable to work Xband, that is about job no. 100. If you can tx on 500 by almeans mail me and we can try to work each other. Regards Ken 73deM0KHW -- O
Jim. Ok Jim. I took your comments in good faith, once you get in the realms of 2KV one does need to be very careful. I will keep you posted with progress, the first task is to have the PA working wit
Hi Alan. The earthy end of the HV winding should be lifted from earth, and a fullwave bridge used . Ken 73 de M0KHW -- Original Message -- From: "Alan Melia" <[email protected]> To: <rsgb_lf_
