Return to KLUBNL.PL main page

rsgb_lf_group
[Top] [All Lists]

Re: LF: Matching transformer for LF and MF question, ferrite material?

To: "[email protected].org" <[email protected]>
Subject: Re: LF: Matching transformer for LF and MF question, ferrite material?
From: "[email protected]" <[email protected]>
Date: Sun, 14 Apr 2019 13:38:35 -0400
Dkim-signature: v=1; a=rsa-sha256; c=relaxed/relaxed; d=comcast.net; s=20190202a; t=1555263522; bh=dYTD6+DSv485WVGrOwgXw1a9wDNqVUjS0WSZFodsVRE=; h=Received:Received:From:Subject:To:Content-Type:Date:Message-ID; b=rkIEyllwwLVqN7xlH55VOkgW5Q+bbwqVEbEQnKPsUSFORMSOeXfLX0kDW5FFzpTVI ig27PtNlwslQtpLYHC/fYVzBSDB87InO7EYH8Of32eCv99ft9MGJk/9j32SZfFUBgY Gx5BWhmZISX3/6t7i3lirr/+zXHtalefnAgASS0mbGy0mv4oAJCIwjEZjRqFOB3c6X YKncx9BA3Kb5I4zrS7SsMy65/3PVlGm3wWgYZWxPTw1UIfuSACxRu5JmsF8c5YJfrJ Xcny8XEQuSYtwae9ZQlXKyoqwHalowcWDxvt7W1cW0riN/3PF8LlvGkyi5p29Ed+LY zj/X0PYmLaaeQ==
In-reply-to: <[email protected]>
References: <[email protected]>
Reply-to: [email protected]
Sender: [email protected]
User-agent: OEClassic/2.9 (Win7.7601; P; 2018-07-03)
Chris

I used the same transformer for both LF and MF operation.

Jay W1VD

----- Original Message -----
From: Chris Wilson <[email protected]>
Reply-To: <[email protected]>
To: <[email protected]>
Sent: 4/14/2019 7:21:28 AM
Subject: LF: Matching transformer for LF and MF question, ferrite material?
________________________________________________________________________________



Hello  LF'ers

I  am having a play listening on LF. I have found the variometer alone
in   my  loading  coil  will  resonate  my  strapped  vertical  feeder
horizontal  quad  loop antenna, I do not need the main loading coil. I
have  a  question  re  the impedance matching transformer though. It's
based  on  a W1VD design, an excerpt from Jay's web site describing it
is pasted here:


~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
The gray box at the lower right houses the transformer which matches
the antenna resistance to 50 ohms. The transformer has a tapped
primary and secondary. The two rotary switches select 12 different tap
combinations that provide a matching range from 12.5 - 35 ohms up to
the 50 ohm transmission line impedance.

The transformer is wound on a stack of three FT-240-77 cores. Each
core is individually wrapped with Scotch 27 glass electrical tape. All
three are then wrapped into a single three core assembly. #14 solid
THHN is used for the primary (14 turn) and secondary (10 turn)
windings. It's important to wind the primary and secondary so that the
turns are interleaved and not wound so that they are on opposite sides
of the core. The primary is tapped at 12 and 13 turns and the
secondary at 7, 8 and 9 turns. Wiring between the switch terminals and
the transformer and connectors is made with flexible #14 stranded
THHN. Eye terminals are used throughout the transformer box, loading
coil and variometer to allow for quick disassembly and repair,
replacement or modifications to the system. All eye terminals are
soldered rather than crimped and brass machine screws and nuts are
used at all connection points.

~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

Will I be OK still using the FT-240-77 cores at MF, both for RX and if
I manage to get my full licence or a friend with one operates here for
TX?  Or  do  I  need to build another with different cores? What type?
Thanks.


  

-- 
Best regards,
Chris                          mailto:[email protected]


<Prev in Thread] Current Thread [Next in Thread>