Return to KLUBNL.PL main page

rsgb_lf_group
[Top] [All Lists]

Re: LF: JT9-2 and JT9-5 mode application

To: "[email protected]" <[email protected]>
Subject: Re: LF: JT9-2 and JT9-5 mode application
From: Rik Strobbe <[email protected]>
Date: Sun, 11 Nov 2018 19:37:27 +0000
Accept-language: nl-BE, en-GB, en-US
In-reply-to: <CANA3B6UJzCmQuHj8H5_J61vG64VhYhmXSBv=YwvCbwDQ93krJQ@mail.gmail.com>
References: <[email protected]>,<CANA3B6UJzCmQuHj8H5_J61vG64VhYhmXSBv=YwvCbwDQ93krJQ@mail.gmail.com>
Reply-to: [email protected]
Sender: [email protected]
Thread-index: AQHUd6mXGlRzs26Lqk2M7O3cP/CWt6VKLHqAgADPmTM=
Thread-topic: LF: JT9-2 and JT9-5 mode application

​Hello Ricardo,


thanks for the feedback.

I haven't used a virtual audio cable (VAC) so far, but I will have a look at it.


73, Rik  ON7YD - OR7T



Van: [email protected] <[email protected]> namens Riccardo Zoli <[email protected]>
Verzonden: zondag 11 november 2018 9:12
Aan: LF Group
Onderwerp: Re: LF: JT9-2 and JT9-5 mode application
 

Hi Rik, all.

The application works fine here, Rik! Thank you for your good work.
I only encountered difficulties adjusting input and output VAC level toward PowerSDR software (TX power slide has no effect and Windows mixer seems bypassed in the VAC settings, so the audio remains at max level).
I'll QRV JT9-1/2/5 LF in the evening.
Thanks to Stefan, DK7FC, for the QSO JT9-1 from last night ;-)

All the best


73 de Riccardo IW4DXW







Il giorno Gio 8 Nov 2018, 22:33 Rik Strobbe <[email protected]> ha scritto:

Dear all,


a few months ago there was a short discussion about a "revival" of the slower JT9 modes such as JT9-2 and JT9-5.

These modes existed in early versions of WSJT-X, and had the advantage of a better S/N treshold level, at the cost of longer transmissions. But unfortunately thse modes were abandoned in later WSJT-X version.

As a result I raised this question in de WSJT-X developers group, but there was no intention do implement these modes again, as the focus was more on the (further) developing of new(er) modes.

Having a closer look at the WSJT-X source code I noticed that the JT9 decoding was done in a separate executable and with some assistance of Joe, K1JT, I managed to write an application that used this executable for decoding.

As this executable only decodes JT9 signals, not JT9-2 and JT9-5, I had to use a lttle trick: speeding up a JT9-2 recording by a factor 2 results in a JT9 signal (at the double frequency) that can be fed to the JT9 decoder. The same can be done for JT9-5 (now speeding it up 5 times).

Some tests showed that this way a JT9-2 signal could be copied at a 2.5dB better S/N treshold compared to JT9(-1). Not completely the theoretical 3dB, but 2.5dB can often be the difference between a failed or successful QSO. JT9-5 hasn't been tested yet.

All this was done "manually" and it was rather time consuming.

So I decided to write an application that I named SlowJT9. It takes care of all the conversions and frequency shifts.

Besides JT9-2 and JT9-5 it also supports JT9(-1) for convenience reasons.

Over the past weeks I tested the application in JT9 mode and after more than a dozen QSO's I feel that it now time to release a beta version.


Whoever is interested can download the SlowJT9 installation file at http://472khz.org/SlowJT9/SlowJT9_setup.exe.


For now only a Windows version of SlowJT9 is available. But as the used IDE has cross platform facilities it should be possible to support other operating systems as well in the future.

The aim of this beta version is:
- To test if the application is working properly.
- To find out if JT9-2 and/or JT9-5 have a sufficient S/N advantage over JT9(-1).
- To find out if there is sufficient interest in using these modes to continue the project.
Therefore all comments, bug reports and suggestions are most welcome via the Blacksheep RSGB LF Reflector, Yahoo RSGB LF Group or directly at [email protected].

73, Rik  ON7YD - OR7T







<Prev in Thread] Current Thread [Next in Thread>