Re: LF: How can you tell if a Class D amp output transformer is starting

To:	LineOne <[email protected]>
Subject:	Re: LF: How can you tell if a Class D amp output transformer is starting to saturate?
From:	Andy Talbot <[email protected]>
Date:	Thu, 3 May 2018 17:05:43 +0100
Dkim-signature:	v=1; a=rsa-sha256; c=relaxed/relaxed; d=gmail.com; s=20161025; h=mime-version:in-reply-to:references:from:date:message-id:subject:to; bh=7HM5W+WFR8mDXwfWgyhcIWd720g5I9iwnSsoX2xqj9Y=; b=alhwamzn86vFs/YAH5Ue3oJeqzOqfC9MU1QWiHLLl1zv+spBYCtQ83TTR284OTo38E G7EBunXdHl166ph6PiZd21i/Byq/L2F8y97x5VQvgzUTTKrR62uBdlAvLJ+pIVBNc3ue PLpdPJrrbIXmy5eNtybITa9KKAaUV8NzNIdiZdpEXKQhha3yF5wqKZHHmRZmimFfkb2J B0PyEHQ7ru+LT5EoS3PmGanpQc02K/OjoNSb2Q2MS/RZgN2XOrisClMk1LSHEgDHJxX7 K6FzjbuKNwRtT4mozFgRuLka9Y1CSJF0SFTku/pm1dxFRcGr3fRcTOrN3y4j21cg6Ki6 iirQ==
In-reply-to:	<[email protected]>
References:	<[email protected]> <CAA8k23Re61N=nn-jqme8=gXTdX8HUtQ7i0B7n2m1qGqagJdYgQ@mail.gmail.com> <[email protected]>
Reply-to:	[email protected]
Sender:	[email protected]

The peak of the fundamental sine component in a square wave is 4/pi times the square wave amplitude (yes, it is bigger). The RMS of the sine is Peak / SQRT(2) . Take the two together and the RMS of your sine is therefore 0.9 * Peak of the square wave

So if you had a Vdd of 50V you would have 45V rms across each half of the winding, or 90V rms across the two halves. Which answers your other question

Actually, thinking about what I've just said, you are putting the square wave though the transformer, not a sine. So in that case you have a bit more leeway in that it can go to the same peak value as the sine would have given you.

Unless I'm building SMPSUs, I don't put square waves though transformers in transmitters - teh RF is always filtered beforehand. There is an equivalent equation for square waves and used in SMPSU design, it is V.t = N.A.B Now V is input voltage, t is the on-time , and N.A.B as before

And yes, your area is correct. 1.58cm^2 = 0.000158m^2

Andy

www.g4jnt.com

On 3 May 2018 at 16:36, N1BUG <[email protected]> wrote:

I am still not sure whether I am using that equation correctly.

Chris, if you will forgive me for tagging along on your post, I'm
trying to get this equation sorted in my head. Put no faith in
anything I say with regard to this! ;-)

Andy, could you please check me out on this?

Let's use the case Chris asks about as an example.

Suppose I want to calculate the maximum RMS voltage to stay out of
saturation.

The manufacturer of the core states its Ae (equivalent cross
sectional area) is 1.58 cm^2. I believe that works out to 0.000158 m^2.

F = 137000

I do not know if I should be using 4 turns or 8 turns for the
primary. It's 4+4. I will assume 8.

Vrms = 4.44 * 137000 * 8 * 0.000158 * 0.1

Vrms = ~77V

Does that look right?

As for practical application I have no idea what this means. The
equation uses Vrms but we're talking about something closer to a
square wave than sine wave. But then it's not really a square wave
either...

Paul

On 05/03/2018 10:00 AM, Andy Talbot wrote:
> By measuring the voltage across the winding using a scope, then
> seeing what Bmax is using teh equation
>
> Vrms = 4.44.F.N.A.B
>
> F Hz N turns A core cross-sectional area in metres^2 B tesla
>
> If B works out higher than about 0.1 for a ferrite core, then you
> are approaching saturation
>
> Andy
> www.g4jnt.com <http://www.g4jnt.com>
>
>
> On 3 May 2018 at 14:46, Chris Wilson <[email protected]
> <mailto:[email protected]>> wrote:
>
>
>
> Hello LF'ers
>
> In say a W1VD power amp, or in general, how can you test if the
> output transformer is
> starting to saturate please? Thanks.
>
> http://www.w1vd.com/137-500-KWTX.html
> <http://www.w1vd.com/137-500-KWTX.html>
>
>
>
> --
> Best regards,
> Chris mailto:[email protected]
> <mailto:[email protected]>

<Prev in Thread]	Current Thread	[Next in Thread>
LF: How can you tell if a Class D amp output transformer is starting to saturate?, Chris Wilson Re: LF: How can you tell if a Class D amp output transformer is starting to saturate?, Andy Talbot Re: LF: How can you tell if a Class D amp output transformer is starting to saturate?, N1BUG Re: LF: How can you tell if a Class D amp output transformer is starting to saturate?, Andy Talbot <= Re: LF: How can you tell if a Class D amp output transformer is starting to saturate?, N1BUG Re: LF: How can you tell if a Class D amp output transformer is starting to saturate?, Andy Talbot Re: LF: How can you tell if a Class D amp output transformer is starting to saturate?, N1BUG Re: LF: How can you tell if a Class D amp output transformer is starting to saturate?, Chris Wilson

Previous by Date:	Re: LF: How can you tell if a Class D amp output transformer is starting to saturate?, N1BUG
Next by Date:	Re: ULF: A new band is opened up! 191 km \| DL0AO results, P. W. Schnoor
Previous by Thread:	Re: LF: How can you tell if a Class D amp output transformer is starting to saturate?, N1BUG
Next by Thread:	Re: LF: How can you tell if a Class D amp output transformer is starting to saturate?, N1BUG
Indexes:	[Date] [Thread] [Top] [All Lists]