Return to KLUBNL.PL main page

rsgb_lf_group
[Top] [All Lists]

Re: LF: Dirty signal

To: [email protected]
Subject: Re: LF: Dirty signal
From: PA7EY <[email protected]>
Date: Mon, 25 Apr 2016 14:45:23 +0200
Dkim-signature: v=1; a=rsa-sha256; c=relaxed/relaxed; d=gmail.com; s=20120113; h=mime-version:sender:in-reply-to:references:from:date:message-id :subject:to; bh=c7SiOIatVr7ylqS60DXkAe+96LQBRmFDa82O+fNWaOc=; b=zzGJ1IDdCYN+q9dCsnM7GevFGrqFe/AemmFCsYSI4jsyxMs0x3N+9oq6MIAA6lFqUg uQLuqsiTra3S9KFcJTXEg62GHHA7M+BZRn8zHi4P3ymkXLfl/HJfiZ7MxXc5lyp2FEoN AkiED6Kxu1t8syW/nhmvTuOiu+dZZagqoV0WKMO2adOINkOid6q5zxr/3S73wJaHwsLW INyDFRZs9Te7t8Fh+9F2b/+sRmZCUkSx1241SReDftd0LkkN3846g9w73Hnu5IenLXNC 8+PTmmOayBk1wcHmcggMMRXFAtFAikHWRBPwz6yaznwJ7OJW907IxZce1MVITtdCz3aQ 6vFQ==
In-reply-to: <[email protected]>
References: <[email protected]> <[email protected]>
Reply-to: [email protected]
Sender: [email protected]
Hi Chris,

Your signal appeared ok here, receiving your signal at a respectable -7 dB.
I saw your question too late to make a screenshot of your signal, saw your WSPR and tuning signal though.

Kind regards,

Ulrich, PA7EY

2016-04-25 14:03 GMT+02:00 Chris Wilson <[email protected]>:
Hello LF 'ers

Monday, April 25, 2016




Best regards,
 Chris  2E0ILY                          mailto:[email protected]


> 25 April 2016


> Had a report that my LF WSPR2 signal was dirty with massive side bands
> on Sunday. I had a look at my setup today found Windows had decided to
> up the audio level from WSPR to maximum into the TS-590 and scoping
> the output of the pre amp and frequency doubler before my G3YXM amp
> showed it looking very ropey indeed.

> I reset it and did a couple of normal WSPR2 transmissions interspersed
> with using the WSPR TUNE function, whilst watching on the G3XXM and
> G4WGT LF grabbers. I am no expert whatsoever, but it doesn't look bad
> now to me. Is this an adequate test to make and to assume things are
> now OK? Thanks.

> Screenshots are at http://www.chriswilson.tv/signals/signals.html


I  managed  to  get a few more minutes on this, and now my SA is fixed
and calibrated I thought some SA screen shots would be useful. I stuck
a  small  rubber duck antenna in the input port and looked at my signal
in  real  time  off  my normal TX antenna whilst actually transmitting
WSPR2.  Tried  with  2  frequency  spans.  Also  took  photos  of  the
scopematch  showing a good V /I balance, and the amp meter set to show
reflected power, which all but nothing. Am I clean....? :)

http://www.chriswilson.tv/signals2/signals2.html






<Prev in Thread] Current Thread [Next in Thread>