Return to KLUBNL.PL main page

rsgb_lf_group
[Top] [All Lists]

Re: LF: TXing WSPR on 630m on a Raspberry Pi, Stefan in QRP...

To: [email protected]
Subject: Re: LF: TXing WSPR on 630m on a Raspberry Pi, Stefan in QRP...
From: DK7FC <[email protected]>
Date: Thu, 26 Mar 2015 23:17:43 +0100
Dkim-signature: v=1; a=rsa-sha256; c=relaxed/relaxed; d=googlemail.com; s=20120113; h=from:message-id:date:user-agent:mime-version:to:subject:references :in-reply-to:content-type; bh=MGLRbynhkOgWtyOAQ1BPdzPhUhdRQAUiIwztnNbUbQc=; b=ZIhnMgKLORQhoKCs0SzKSs0RBe0rD2En0BT6PKyl2mHfxSnSPilVPQ+jnRscu96MLI bAVaAVUHmX4LFKGKMft/wujgnQH1w2PRb73Cl7eoW1yacIBO9fAv1XMtysodxd9KjQvS ThxfCer/R/splOx4XAQafVO1ohsJNfpg5/HqlwTUs3MdSzchRE4Nb7AdqsH/FDQhrwak BX3BzSH7poGFt8KyX6bag8OB0DGpmJRhSW42ARqW+eLlp/jVrtdsguqGAYE2mzaZiA/5 MEOAvIxwvZPbf3cJeDAck05ivEtxIE+/c2pOg1JCb2NjlV9j1Qxq1NIhESREgrZxhY9p 6xHg==
In-reply-to: <[email protected]>
References: <4698D0522AFD45F896A41F2D16A2D831@AGB> <BC1061758A4D4230AA9719C22735EBF4@gnat> <19EEF7A6DD30462FA6ACC0F015DC9F52@AGB> <[email protected]> <[email protected]>
Reply-to: [email protected]
Sender: [email protected]
User-agent: Mozilla/5.0 (Windows; U; Windows NT 6.1; de; rv:1.9.1.8) Gecko/20100227 Thunderbird/3.0.3
Hi MF,

I'm now running the 7667 at 13.8V supply voltage. The MOSFET driver is easily keyed by the Raspi, directly with its rectangular output. I measured 0.5 W TX power at 50 Ohm. This is what i'm running tonite on 630m.
Not a real PA, just the Raspi and this IC in a DIL-8 case. Fascinating!...

73, Stefan


Am 23.03.2015 16:11, schrieb DK7FC:
Hi MF,

I've added a simple ICL7667CPA MOSFET-driver to the GPIO of the Raspberry. It's power supply is 5V coming from the GPIO itselfe. This leads to a 5V rectangular signal with lower output impedance. I've coupled the output matching circuit so that the output power is now 50 mW / 17 dBm, i.e. 7 dB more power then in my previous test.
Iamge:  https://dl.dropboxusercontent.com/u/19882028/MF/17dBm%20RPI%20WSPR.jpg

The beacon is running now on 475.685 kHz.

73, Stefan/DK7FC


Am 18.03.2015 21:45, schrieb DK7FC:
Hi MF,

Today i've got i 3rd Raspberry Pi. I quickly installed the WSPR softaware and since a few minutes i am transmitting WSPR-2 on 630m, my usual frequency 475.685 kHz.

I'm directly using the GPIO output pin, without an amp stage behind! The rectangular 3.3V output voltage is passing a cap and an isolation transformer (FT50-77) as well as a simple pi-filter, because it is a Raspberry pi! ;-)

See: https://dl.dropboxusercontent.com/u/19882028/MF/Raspberry%20Pi%20B%2B%20WSPR%20TX.jpg

I measured an output power of about 10 mW at 50 Ohm. It is now connected to my MF antenna and transmits in a 100% duty cycle. I still have to learn how to reduce it but this will not take long.

With 10 mW TX power i managed decodes by 3 stations now.

3 spots:

Timestamp Call MHz SNR Drift Grid Pwr Reporter RGrid km az
 2015-03-18 20:32   DK7FC   0.475684   -21   0   JN49ik   0.01   DH5RAE   JN68qv   345   98 
 2015-03-18 20:12   DK7FC   0.475685   -24   0   JN49ik   0.01   F1AFJ   JN06ht   667   247 
 2015-03-18 20:06   DK7FC   0.475683   -27   0   JN49ik   0.01   DL1DBC   JO41bi   217   349 


Does someone have good ears to get a decode from me? :-) It is a challenge! :-)

73, Stefan/DK7FC

PS: The signal is so weak that my RX antenna frontend is not overloaded, so at that power level i can transmit and receive to the same time :-)
PPS: A small amp stage will follow soon, i intend to use an BS170 running at 5 V.
<Prev in Thread] Current Thread [Next in Thread>