Interested in the SpecLab configuration file :-)
Could it be made available via web link or e-mail?
Many thanks
Daniele
________________________________
Da: [email protected] per conto di Stefan Schäfer
Inviato: ven 02/04/2010 13.09
A: [email protected]
Oggetto: AW: VLF: 4th VLF experiment by DK7FC/p
Hi Gary, VLF, LF,
The locator is JN49IS. In older mails i have given you the exact coordinates.
In google maps you can find the QTH within a sector of some 10m.
QRG is 8,97000 kHz. The 4mHz settings is optimal! If the SNR will be good, you
can try 8mHz as well or 15, like Markus did it at the end of the tests. 15mHz
seems to be optimal for DFCW-120 but i will start with DFCW-600...
I will have no internet access until saturday night, so cu after the experiment.
Hopefully the wind will be strong enough, the forecast shows about 20km/h from
south. This would be enough...
Best 73 es gd RX! :-)
Stefan/DK7FC
________________________________
Von: [email protected] im Auftrag von Gary - G4WGT
Gesendet: Fr 02.04.2010 11:52
An: [email protected]
Betreff: Re: VLF: 4th VLF experiment by DK7FC/p
Hi Stefan, LF,
I will be monitoring your frequency using a M0BMU type 30 turn 0.8M square loop
and 9kHz pre-amp into my PC sound card, software is SpecLab running Marcus's
"9kHz_4mHz" configuration. This loop system has increased my reception of the
Alpha signals by about 10db giving up to 25db SNR. Thanks to Jim for a great
design.
Stefan, can you tell me the QTH locator for your Tx site please.
Good luck with the 4th test.
73
Gary - G4WGT.
2010/4/2 Stefan Schäfer <[email protected]>
Dear group,
After a break of one week i plan to transmit again on VLF / 8,97 kHz. If
the wind will be enough i will come up on saturday, 3. April, at arround 10 UTC.
The DFCW-600 mode was a good choice in the last experiment, so i will keep
this mode.
If Markus/DF6NM has time to make QSP on the mobile phone to the reflector
(Markus ?) we could arrange various tests. I will also call other local
stations for reception reports during the transmission.
There will be some new components to test:
Today i started building up the 600W class D PA (at least 600W) that is
directly fed out of the 230V (rectified) of the generator. PTT and VFO input is
realised by fiber optic cables. The DC capacitor is 2000µF/350V and can be put
on voltage without a NTC or charging resistor due to the relatively high output
impedance of the small generator (tested). This works very fine now. Tomorrow i
will apply the FETs and the big ferrite core and it's windings. Then i will do
a test on a dummy load at home. If the signal will be 3dB stronger, we could
theoretically change to DFCW-300 compared to the last experiment. But there are
many OMs writing private mails to me and prepare to be QRV on this next test.
Some of them are using E-Field antennas and/or are more than 860km away, that'
why i want to stay in QRSS-600 first. So there might come a new distance
record? In any case it will be exciting to me watching the new system running
:-) Also it will be interesting to see if the E-field antenna will get the
signal!
The primary winding of the TX coil is increased from 9 to 13 turns due to
the higher power that will be applied. Otherwise the current will become to
high.
I will mount the amperemeter (analog, 1A) into the coil. That makes it
easier to adjust to resonance and watch the stability and maximum and average
(estimation) current.
Finally i will try to apply some copper rods into the earth and will look
how the antenna current is changing.
The goal is to radiate 4mW ERP. Another goal is to reach as many stations
as possible. So i would be pleased if YOU would be one of them. :-)
Since the QRM/QRN comes up in the late afternoon and transmitting for 4...5
hours i will close at about 15 UTC. So the planned LF activity is not affected
:-). Sorry, but i cannot participate on the LF acty later since the VLF coil
takes all the place in my car ;-)
I looking forward to this experiment and wish you good luck and fun by
receiving :-)
73 es gl, Stefan/DK7FC
PS: Could you give me a short feedback if you plan to be RX?
<<winmail.dat>>
|
