Return to KLUBNL.PL main page

rsgb_lf_group
[Top] [All Lists]

LF: Re: RE: Re: 500KHz first Olivia QSO ???

To: <[email protected]>
Subject: LF: Re: RE: Re: 500KHz first Olivia QSO ???
From: <[email protected]>
Date: Fri, 2 Jan 2009 17:40:57 -0500
References: <00c301c96d20$5314e870$6401a8c0@asus> <002c01c96d23$40f523a0$6c01a8c0@DELL4> <010301c96d25$ee1e9910$6401a8c0@asus>
Reply-to: [email protected]
Sender: [email protected]
Gary
 
Congratulations to you and Jim! I look forward to having a 'digital' T/A QSO once we establish which is the best mode.
 
Jay W1VD  WD2XNS  WE2XGR/2
----- Original Message -----
Sent: Friday, January 02, 2009 5:03 PM
Subject: LF: RE: Re: 500KHz first Olivia QSO ???

Hi Jay,

 

Well OK then, first UK Olivia QSO!!!!!

 

73

 

Gary.

 


From: [email protected] [mailto:[email protected]] On Behalf Of [email protected]
Sent: 02 January 2009 21:44
To: [email protected]
Subject: LF: Re: 500KHz first Olivia QSO ???

 

WE2XGR/2 and WE2XGR/3 have QSOed in this mode on 500 kHz...and just about all other modes as well...

 

Jay W1VD  WD2XNS  WE2XGR/2 

----- Original Message -----

From: Gary - G4WGT

Sent: Friday, January 02, 2009 4:23 PM

Subject: LF: 500KHz first Olivia QSO ???

 

Hi LF,

 

Is this the first Olivia QSO on 500KHz??

 

 

CQ CQ m0bmu m0bmu m0bmu kkk

 

CQ CQ CQ DE...g0nbd  g0nbd  g0nbd 

 CQ CQ CQ DE...g0nbd  g0nbd  g0nbd 

 CQ CQ CQ DE...g0nb

 

m0bmu ... ok jim  uBg0ndb g0ndb de m0bmu m0bmu m0bmu m0bmu

 

copy ok ???  how me ??*Fbh)]Fg0nbd g0nbd de m0bmu m0bmu m0bmu ok Graham good copy herT most of the time (.. A^s_ still trying to figure out the software still - btu graham de m0bmu kkkm0bmu de g0nbd

 

ok dr jim .. well your signal is quite loud on the speaker ! 

 

fine copy 100%  what is your peak power o/p ????

 

nice to  work you for the first time ..

hr running   30 watts , racal ma1723/ra1778 with skanti  pa block .. multipsk ..

 

ae  35 ft top load vertical .. inv L config

 

ok ??btQJ4`xwo,g0ndb de m0bmu r ok 100% some QSB here, but still good copy when ur sig barely audible. Am running around 90W to 10m high, 40m long inv L antenna from EER transverter and IC718 with multipsk also. My ERP should be close to 1W BTU graham de m0bmu kkkR`^ijLm0bmu de g0nbd

 

ok jim fine .. well all 100%  even in a deep qsb dip your signal fell under the noise .. but still printed fine ... looks like a good mode ..hihi/..  i used  250 hz 8 tone in the past and this gave a good copy under qsb .. better than psk ..

 

your signal is very clean from the tx .. no splillage .. looking on spec-lab and can only see same as my ouit going .......

 

ok .. well  fine on the 1 wat erp .. after destroying my skanti  pa .. im keeping

power down hihi

btu jim ???

 

g0ndb de m0bmu lost u suddenly there, was a bit worried PA had had a nasty accident again hi. Lost a few words in first half of your over, but mostly OK. Yes, output should be fairly clean since not really any amplitude modulation in this mode anyway - so could use class D tx and keep things a bit simpler. You mentioned narrower mode - I see there is 250hz and 500hz bandwidth variants, wonder how they compare - would not get as many complaints about bandwidth, hi hi. BTU Graham de M0BMUkkkSd

 m0bmu .. de g0nbd

 

ok fine jim .. well 100% copy that over again .. i pressed the rx button and the tx stopped hihi

 

well this was a quick test to  see if this mode printed better over the noise ...looks to  work very well 

 

could   change mode ?   8 x 250  that would give a good test ,  reduce to    8 x 250   8 x 250 ???

 

bkbkbkbk

 

ok graham g0ndb de m0bmu, if you QRX will try to change over to 8 x 50 mode now - pse qrx...ok  changing to  8 x 250

 

73,

 

Gary - G4WGT - IO83QP.

 

<Prev in Thread] Current Thread [Next in Thread>