Return to KLUBNL.PL main page

rsgb_lf_group
[Top] [All Lists]

Re: LF: RE: K1JT WSPR BEACON 503 KHZ - NOW TILL LATER !

To: <[email protected]>
Subject: Re: LF: RE: K1JT WSPR BEACON 503 KHZ - NOW TILL LATER !
From: "Graham" <[email protected]>
Date: Sun, 30 Nov 2008 00:12:39 -0000
Importance: Normal
In-reply-to: <[email protected]>
References: <C12A5F115FCC4688B67B61DAF096757F@ns94d01ae4d850><B912A8A5763D45448447109866FC713E@AGB><006701c95262$15df2cf0$6401a8c0@asus><[email protected]><467399265F80446CB93A56E6A4C11509@AGB> <[email protected]>
Reply-to: [email protected]
Sender: [email protected]

Ok Rick

Well , there is a qso mode for wspr .. its on the download site .. but ive not had a look at it yet...

On the rx tune ... ok ... its a little confusing as the dial frequency is normally given ... however . the audio tone frequency is the differance of the carrier and the dial frequency ... I have set 10.1000 and 10.101500 to give me a true 1500 tone , the exciter is set to 501.5 usb ..

CW reception .. I don't know if the system works in either sense .. ie tx set usb and rx set lsb ....However as long as the bfo is stable and on the same side as the usb filter carrier insertion oscillator you can use the narrow cw filter as the shift is I think 2 Hz !

Assuming your cw filter is centred on the IF pass band ... ie dial frequency ..... if you tune to a known signal with the filter 'in' (zero beat) with the rx audio fed to say 'spec-lab' set the bfo to 'on' and vary till the beat note shows 1500 hz on the analyzer

Re set your dial frequency to 503 Khz 'dead' and the recovered audio will be cantered on 1500 hz ....

nb-- due to the 'extreme' (for want of a better word) audio processing , signals within the audio pass band will not affect decoding unless they are on the same frequency ... unless they are blocking the rx


Hope thats ok ?

Tnx - Graham ..





--------------------------------------------------
From: "Rik Strobbe" <[email protected]>
Sent: Saturday, November 29, 2008 10:47 PM
To: <[email protected]>
Subject: Re: LF: RE: K1JT WSPR BEACON  503 KHZ - NOW TILL LATER !


Hi Graham,

right now your signal coming up, weak but audible with CW filter.
As I just downloaded & installed WSRP I followed the instructions that
say receiver in USB at -1500Hz of the desired RX frequency. That
worked well with the SSB filter (despite the awfull noise at 2700Hz
bandwidth).
But the instructions are "basic" as is the help function.
If it would be possibe to decode at 800Hz audio I could use the CW
filter and win a lot of dB's.
As I understand WSPR seems a "monitor mode", any option to make a QSO
(ie. exchange reports)?

73, Rik  ON7YD -OR7T


Quoting Graham <[email protected]>:

Ok Rick

Thanks for report .. also  your  test or7t last night  5/5/9

Tnx- G ..

--------------------------------------------------
From: "Rik Strobbe" <[email protected]>
Sent: Saturday, November 29, 2008 10:10 PM
To: <[email protected]>
Subject: Re: LF: RE: K1JT WSPR BEACON  503 KHZ - NOW TILL LATER !


Graham,

here (jo20IX) good copy at -25dB

73, Rik  ON7YD / OR7T



Quoting Gary - G4WGT <[email protected]>:

Hi Graham, LF,



No problem here.



081129 2012 36 3 1.3 0.502999 G0NBD IO83 27 0 1 0

081129 2016 36 4 1.2 0.502999 G0NBD IO83 27 0 1 0

081129 2022 36 4 1.3 0.502999 G0NBD IO83 27 0 1 0

081129 2030 37 4 1.1 0.502999 G0NBD IO83 27 0 1 0



73



Gary - G4WGT.



 _____

From: [email protected]
[mailto:[email protected]] On Behalf Of Graham
Sent: 29 November 2008 17:34
To: [email protected]
Subject: LF: K1JT WSPR BEACON 503 KHZ - NOW TILL LATER !





Hi Lf ..



Running  K1JT  WSPR  beacon   20 % tx



Carrier  frequency   503 KHz



Dial set   501.5 Khz usb , audio tone 1500 Hz



Running  approx  75 watts to  35 ft top loaded vertical ,

(If the pa trips beacon will continue at -14 db level)



Reports welcome



Tnx - Graham



G0NBD / IO83LK









Disclaimer: http://www.kuleuven.be/cwis/email_disclaimer.htm







No virus found in this incoming message.
Checked by AVG - http://www.avg.com
Version: 8.0.176 / Virus Database: 270.9.11/1819 - Release Date:
11/29/2008 10:37




Disclaimer: http://www.kuleuven.be/cwis/email_disclaimer.htm







No virus found in this incoming message.
Checked by AVG - http://www.avg.com
Version: 8.0.176 / Virus Database: 270.9.11/1819 - Release Date: 11/29/2008 10:37




<Prev in Thread] Current Thread [Next in Thread>