Hello Horst, Around midnight I (think i) copied your signal for around 1 hour. See attached picture (around 693Hz) it's a very weak signal. Later the signal of DI2AM om 505.180KHz goes down and I saw
Merci Michel, Yes it take a while due a homemade QRM source. I bought last summer a 10MHz GPS controlled OCXO for my 10GHz Transverter and this oszillator create a lot of noise over the 500KHz band.
Hello Wolf, big signal in SpectrumLab with the configuration files from Markus - see attached picture. Ok luckly our QRB is something around 1.5-2km only. Looking forward when you send QRSS. So far i
Good morning, Stefan, DK7FC is transmitting now on 9KHz. You could see it on his grabber http://www.iup.uni-heidelberg.de/schaefer_vlf/DK7FC_VLF_Grabber.html I had a short chat with him a couple of m
Hallo Wolf, Rx laeuft wieder. Diesmal auf einem anderem PC. Auf diesem PC habe ich den Eindruck weniger Hintergrundgeraeusche und 50Hz Brumm zu haben. Wie auch immer ich glaube es ist wieder nichts z
Oh sorry mail was direct for Stefan and Wolf Vy73 Marco, DD7PC Von: Scholz, Marco [ICG-IT] An: '[email protected]' <[email protected]> Gesendet: Sun Jun 13 13:06:46 2010 Betreff
Hello Henny, many thanks for nice report. I tested yesterday my existing antenna with a new, better earth connection and transmitted just with 35W. It was hot in my shack. Normally the Ropex has a be
Hello Stefan, I used the standard settings of SpectrumLab V2.75b11 BETA in Mode QRSS 120sec/step, 2mHz resolution, with SR CAL. vy73 Marco DD7PC Hello Stefan, I was using the "standard" 9kHz_4mHz set
Hello Stefan, think i copied your transmission today. I received a signal */- 6469.97 from around 16-17:30 local (CET) time. I used a Miniwhip antenna with SpectrumLab Qrss120, 2.0mHz. My locator JN4
Oh good. I switched on my RX and hope Markus will continue sending for a while? 73 Marco, DD7PC Dear VLF, DF6NM is transmitting now on the Dreamers Band! His signal is copied on my VLF grabber in DFC
Hello, I was receiving the last hour. Unfortunately I set QRS120 insted QRS600 which was set at the Grabber. In QRS120 I could not see any signal, sorry.. vy73 DD7PC Hi all, I've been in touch with S
Hello Henny, That was my signal "PC". The p is in QRS60 and the C in QRS240. I was testing my stabiltiy with DK7FC's qrs240 Grabber. Thanks vy73 Marco DD7PC Hi LF, Capture unid, henny cpm 73s Het ber
Thanks Stefan, I was a while offline to optimize matching. I transmit now with 135W in QRSS60. After sending my call (which take around 60min) I change to 35W and QRSS240. vy73 Marco DD7PC ...is curr
Hello Lubos, Good copy 20d! over noise. You rx also 80m for crossband? Vy73 Marco, DD7PC Hello LF! I am transmitting on 501.888kHz. Does somebody see my signal? Lubos, OK2BVG
Hello LF, Stefan, DK7FC is transmitting with his 600m earth antenna on +/- 137.715KHz in DFCW4. I could see him on my Grabber (see attachment) http://www.qsl.net/dd7pc/lfgrabber_dd7pc.html and on the
Hello Lubos, You 30dB over noise in JN49ax! Vy73 Marco DD7PC Hello LF! Due to local QRM I am going to start my transmitting on frq 501.888kHz, mode QRSS3. Thanks for all calling! Lubos, OK2BVG
Good morning Henny, Thanks report. I was the "P" yesterday evening. vy73 Marco DD7PC LF, Capture P henny cpm 73S Het bericht kan nu met het volgende bijlagen of koppelingen worden verzonden: P 12-09.
Good evening John and Stefan, Thanks for report. Very happy about 10dB over noise for my small setup. Calling for a whils CQ on +/-137.700 in QRS3 and change later to QRS60 on +/- 137.781. Sorry shou
Hello Lubos, As mentioned yesterday here now attached a screenshot of your signal. Thanks again for nice QSO yesterday evening, 20:15UTC. OK2BVG, 501.888KHz, QRSS3 -- DD7PC, 3570KHz, CW Wish you a ni
