1200km!!!! new record for me!! With best regards Jim From: [email protected] [mailto:[email protected]] On Behalf Of Lubos OK2BVG Sent: 20 January 2010 19:24 To: rs
Will do! I am getting several decodes of your “G4WGT QRZ” call all at around -15dB. There is another occasional signal on evens but not decoding I am running 10W from ICOM 706 mk2G into i
RF Link Budget Calculator Results Dear All I have been inputting some numbers into the calculator from the link below, clearly some assumptions need to be made as well as guesstimates but this may be
We are obviously mainly engineers here!. A question was asked, and has been responded too in some considerable depth and detail and diverging opinions proffered. The questioner now knows a little mor
Dear LF, Has anyone any ideas or suggestions on a resource for calculation of a link budget for WSPR over a set distance? As it seems I can get up to GM4SLV reasonably consistently on my current ante
Hi Gary Just got two decodes of you at -12dB and -15dB 2116 and 2118. I have replied with my call and locator on odd minute txing With best regards Jim Dr. James Cowburn E blocked::mailto:james.cowbu
At G7NKS, the biggest culprit for RFI is the plasma screen in the lounge! The XYL is watching the "Witless Silence" and Jonathan Woss and it causes havoc from LF to 20m. It's an old (2001) NEC displa
Thnx Rik, there’s not much between me and you though, just the east England fens and then the north sea!! Jim, you are good copy here (-18dB). 73, Rik ON7YD - OR7T Van: owner-rsgb_lf_group@blac
Hi Lubos I am getting G3XBM but we are only abt 50km apart With best regards Jim Dr. James Cowburn G7NKS From: [email protected] [mailto:[email protected]] On Behalf
Dear LF, Thanks to all for the informative answers. It's a bit like working with Pharmaceutical Regulators whose stock answer is "it depends"!! Seriously thanks loads With best regards Jim Dr. James
Sorry but my appliance was operated incorrectly and so I hadn’t transmiited! I am now sending and also rxing G4WGT at -14db to -8db From: [email protected] [mailto:owner-rsgb_l
Hi Roger I have managed 1020km D?RAJ on my old Tx before it expired. TF3 would be great though. 73s Jim From: owner- [email protected] [mailto:owner- [email protected] ] On Beha
Dear LF, I have acquired a Racal Dana 9084 signal gen but I can’t seem to get any output and the frequency display is flashing. I have tried to google for a manual to no avail. Has anyone got a
Hi Eddie I have a trace of your QRSS using DM780 on 503.218. Time 10.25z My locator is IO92ub. Rx. IC706mk2g Ant Inverted L 7m vertical/28m top hat radial, fed via 400uH tapped coil and impedance txf
Amateurs using the washing machine??? Good god man....heresy!!! With best regards Jim Dr. James Cowburn Hi John, Markers were every 15 seconds. Also the whole thing was repeated every 5kHz going up i
Dear LF, Going thru a newly acquired junk/spares box I have found a new/wrapped in plastic Marconi Crystal Oscillator Identity FQ 3121-11. Serial no. 118941. It is stamped as having a freq of 4960KHz
Dear All, Thanks to G3XIZ I am now QRV on 136.5. I will be sending CQ CQ CQ de G7NKS de G7NKS from 15.15z onwardsat around 5min intervals Thnx for any rports With best regards Jim Dr. James Cowburn 2
Hi Rog Run the WSJT7 programme and select wspr mode If you receive a signal in the window using the spectrum display click on it and click decode When you have callsign and locator decoded in the mai
Sorry I knocked the VFO! Thanks for the report --Original Message-- From: [email protected] [mailto:[email protected]] On Behalf Of James Moritz Sent: 07 February 20
