Clemens, LF group! This is exactly the opposite that I experienced with the Mini-Whip. The higher I brought it up (= the farther I brought it away from the noise source, commonly called "house"), the
Mal ! I was talking about the "cheapest" 10m pole and as far as I can see on the web-page it is for 30.... Don't know about pounds but 30 is at least a very fair price! I personally one 2 of those 10
John, Stefan, LF! Not sure if all of you have noticed, but Ossi, OE5ODL is providing such a signal nearly all the time around 137775. It would be ideally suited for Stefan because it's very well outs
Markus, LF! Thank you for your accurate QRG. I used it to calibrate my OXCO which is used for calibrating my grabbers. I was off for 200mHz but now I think this offset is corrected. Nice signal here.
Henny! Just take a look at: http://www.dx-wire.de/brit/ To support a small probe or a vertical wire the cheapest 10m pole is suitable and I think the price is really o.K. For my LF-Antenna with the t
Roelof! With interest I was following all the discussions about the "Mini Whip"-like antennas. In your description of the "PA0RDT Mini Whip" you suggest to use a non metallic pole for mounting the pr
John! Actually there is no special guying used since the mast is only the lower (and thus thicker) section of an originally 10m high "cheap" Fibreglass-Pole like available at http://www.dx-wire.de/fi
Roger, Costas, LF! I had a similar problem with an Acer Aspire One but running SpectrumLab. Everything above 8khz wasn't displayed but finally I was able to fix it by installing another audio-driver.
Hello group! I just shut down my LF-grabber http://members.aon.at/grabber because the antenna is damaged. Yesterday evening a fibre pole on the roof got loose and fell down. On top this pole are the
Hello group! I just shut down my LF-grabber http://members.aon.at/grabber because the antenna is damaged. Yesterday evening a fibre pole on the roof got loose and fell down. On top this pole are the
Dear group ! I brought my LF and VLF grabbers online again after a longer period where they were out of service due to a damaged antenna. After an ice-rain a few weeks ago, the wires of my LF-TX-ante
Hello Markus ! Tnx for the report. Yes it's my QRG. I currently running about 600mA of Antenna current. The WX is excellent, no wind and cool temperatures which helps to keep my PA cool. I observed s
Hello Peter! Maybe it will be possible for me to transmit tomorrow. Of course it all depends on the wind. But if there is a chance, I will fire up my TX at about 900z. 73 OE3GHB Gerhard Am Freitag, d
Hi Peter ! I strongly would recommend to use the "1 Pixel per Pin" option. It would make the display much clearer. Right click on to the frequency ruler and check the option. 73 OE3GHB Gerhard Am Mit
Stefan! I just switched the output-mode of my TX to "positive energy". Try to catch some. On my PA there is a switch with 3 positions...."negative", "neutral" and "positive".....:-) 73 es tnx for wat
Correction.... of course the top-load is horizontal. I mixed up my wishes with reality, 100m vertically would be so nice......:-( 73 Gerhard Am Montag, den 05.03.2012, 20:55 +0100 schrieb Gerhard Hic
Gentlemen! Finally, I have stopped about 1700z. Thanks to everybody who was trying to pick up my signal. The test with Lubos, I did this morning revealed some problems in my RX-system which I'm going
Hi Eddie! Finally my signal is visible on your grabber! So I wanted to stop about an hour ago but I will leave it running now for a while. 73 OE3GHB Gerhard Am Samstag, den 10.03.2012, 13:47 +0000 sc
Dear group! The weather forecast for tomorrow looks promising. Only weak wind to expect here. This gives me another chance to transmit on VLF tomorrow. If everything goes well, I will start around 80
Hi Eddie! Yes, I can see that on every grabber online, the noise is raising. Even at Lubos new QRSS30 window my signal is fading out now. So I think it's time to stop this transmission for now. The g
