Should have added the credentials too :- * Made it to the Czech Republic * Eddie Hi Ha-Jo MAS 500kHz :- My complete TX - CW, QRSS, WSPR, 70mm X 55mm X 75mm a bit fat maybe but I recon that is shirt p
I have in mind a Camping trip, go stay in a field near Roger and have a few contacts on WSPR and ROS. No need to take a radio, just stick the soundcard In/Out to a couple of ground stakesJ Eddie --Or
My 500kHz WSPR TX is off, now listening on my Marconi T in readiness for G3XBM test Eddie G3ZJO IO92ng --Original Message-- From: [email protected] [mailto:owner-rsgb_lf_group@blacks
I was checking out some of you folks web sites and one of them had an article (pdf) about gas pipe lines and how signals were sent down them to >check them out. I started to read it and was called a
Strapping the feeder on the doublet dropped Jim’s signal by 10dB, just like when I tried TX’ing using it with a loading coil. The ends slope low and it shields itself. Un strapped at 20:1
No copy of Roger at all on this session. Jim is 10dB down on his loop. Did Mal make a joke about your set up Roger. ‘Your Radiators are radiating’ if they are painted white they are alrea
OK Roger, as you know, I am not so surprised, I will att. my equivalent circuit Idea where the house is the antenna. See what comments ensue. 73 Eddie --Original Message-- From: owner-rsgb_lf_group@b
Roger I see you very weak, no decodes 10:48, 10:58, 11.12. A small shift LF or 20Hz HF would get you away from the Plasma TV lines, there is one adjacent HF which may be killing you. Eddie --Original
At -31dB you are a barely visible trace on the Vertical here. I saw a trace of you at 19:18 which did not de-code, then changed to the 40m doublet which is basically horizontal and produces better DX
Hi All I think I will add a 600ohm 1:1 transformer to my sound card LF set up in addition to the diodes I have at present. Incidentally it has suddenly struck me what a loose term 'back to back' diod
Roger What were you using at 12:34.? I see a faint trace of your transmission, no decode. BTW the Panasonic Plasma noise has gone off and yes I checked the drive, the car has gone. Eddie --Original M
Me too, I just read yesterdays post and was about look, only one day late, on the ball me. Eddie --Original Message-- From: [email protected] [mailto:[email protected]
A little finger trouble from G :- 3) Non linear PA is required He means:- 3) No linear PA is required Eddie --Original Message-- From: [email protected] [mailto:owner-rsgb_lf_group@b
Hi Ha-Jo MAS 500kHz :- My complete TX - CW, QRSS, WSPR, 70mm X 55mm X 75mm a bit fat maybe but I recon that is shirt pocket size N.B. Does not include the Antenna. No Computer for the WSPR. Consumes
is a >pumping station and I was wondering if I would be able to receive these >signals. This is off topic for this reflector but I was sure I that I seen >it on one of these websites. Anyway thank y
CORRECT Mal, I totally agree. G4AYT. I don’t want to join in with any tit for tat stuff, please don’t lets go there. Mal has very good antennas I am sure he can receive my 500kHz QRPp si
Hi Harry Yes it has 8.9kHz QRSS settings in the menu and it works very well. I find it much easier to use these as a starting point for experimenting. Eddie G3ZJO --Original Message-- From: owner-rsg
Hi Stefan Yes that's much better as a term; it had escaped fro my grey cells for today. No doubt next time I shall call them 'back to back'. I now have an old 56k voice Modem less its S Mount 600ohm
Very nice Roger, I checked my spread sheet, it is the same signal strength -26dB, as you received me on your Spiral Top Loaded antenna. Eddie G3ZJO IO82ng --Original Message-- From: owner-rsgb_lf_gro
