Return to KLUBNL.PL main page

rsgb_lf_group
[Top] [All Lists]

LF: Re: RE: Field Strength Measurements

To: <[email protected]>
Subject: LF: Re: RE: Field Strength Measurements
From: "Alan Melia" <[email protected]>
Date: Fri, 8 Apr 2016 00:21:34 +0100
Dkim-signature: v=1; a=rsa-sha256; c=relaxed/relaxed; d=btinternet.com; s=btcpcloud; t=1460071286; bh=AuI6C+BzIzcCUw6ZP5UBirDczN+vgwOH/GZmnIxawjo=; h=Message-ID:From:To:References:Subject:Date:MIME-Version:X-Mailer; b=rI/+DLFVOhYCdQhQNdxTY9NCoFWeLtHy/TRCigzscIliLjESY4jDBEejJz8muSGtTjp81IcBx+1ANi3syScO0xXQTOmZwfzyeAuFXHfme6Kney9xTK7Ou9XicuatFWf9tu9d9hN0yD/1xtgsmKIP4woLkmX8Tp1dTH6yQBgA5ns=
References: <1840555212.2044542.1460066335241.JavaMail.yahoo.ref@mail.yahoo.com>,<[email protected]> <7E7DFBB4D102A04DB5ADC88D66628A4A444EBB97@ICTS-S-MBX1.luna.kuleuven.be>
Reply-to: [email protected]
Sender: [email protected]
Chris two other points
1.  How far from the aerial are you taking the measurement .....you need to be at least 300 to 500 metres away
2   Because of ground loss problems even the best (fully in the clear) amateur short aerials measure around 5 to 6 dB low.(that is a 136kHz observation.) Often a better reading is taken say a mile away on slightly elevated ground to the aerial site. Jim Moritz did tests in a field adjacent to the Puckeridge Decca mast, with a 10m high inverted L.
 
Alan
G3NYK
 
 
----- Original Message -----
Sent: Thursday, April 07, 2016 11:24 PM
Subject: LF: RE: Field Strength Measurements

Hello Chris,

 

(1) will give you the EMRP (Effective Monopole Radiated Power)

(2) will give you the EIRP (Effective Isotropic Radiated Power)

The formula P = 0.0203252(Ed)^2 will give you the ERP (Effective Radiated Power)

 

73, Rik  ON7YD - OR7T

 


Van: [email protected] [[email protected]] namens Chris Osborn [[email protected]]
Verzonden: donderdag 7 april 2016 23:58
Aan: LF Group
Onderwerp: LF: Field Strength Measurements

LF,

I've recently resurrected my old RF field strength meter as designed by PA0SE and published in the LF Experimenters' Handbook.
I've modifed it to measure signals in the MF band and have calibrated it with a home made Helmholtz coil arrangement.

This question may have been raised before but PA0SE gives the formula for deriving the transmitter power as

P = 0.0111 (Ed)^2  . . .   (1)

where E is the electrical field strength and d the distance

I've read in other places that the power from an isotropic radiator is

P = (Ed)^2 / 30

i.e.  0.0333 (Ed)^2  . . . . (2)

My calculated radiated power seems rather low so I'm wondering whether I should be using formula (2)

Any clarification would be most welcome.

73
Chris G3XIZ







<Prev in Thread] Current Thread [Next in Thread>