Return to KLUBNL.PL main page

rsgb_lf_group
[Top] [All Lists]

Re: LF: Fire in the wire

To: rsgb_lf_group <[email protected]>
Subject: Re: LF: Fire in the wire
From: Warren Ziegler <[email protected]>
Date: Fri, 26 Apr 2013 17:47:51 -0400
Dkim-signature: v=1; a=rsa-sha256; c=relaxed/relaxed; d=gmail.com; s=20120113; h=mime-version:x-received:in-reply-to:references:date:message-id :subject:from:to:content-type; bh=p1vuSf2QtXfX5t5csPsnk5Xv2mxjxJiyzt0eipv++hE=; b=u8gXIZEwK3dnMkdXP2U8uxmohJuCUjy01fg13bPPmrSBywYXWiMOvhHin3t8UHXSup RhBmXdo/esWMgsmDBelMg2moGTi+Bmj0S7XOEP4raD2TEzWJJ7mNXRtgk6iuQTnVCG3z 2AW80B9BM/vOVeO+J8HX3DqdGTf8WAooPN8Wz+tJ3vQZEYF4n9tn00DAUaTo+koCbzUi DESsXFFtpTEpWsR0mz7I4Zp6T3dgPW5TGq2XjfVvcEtD8p5Z4GxBmXfE/ucRDDcNxdcM CNVSU8ogxBiKwm3ILrZ/DDCyhRFXflLqwPjjgcLxWgUh5jW8Xjv3q64duLv/w/NgouRa QRrQ==
In-reply-to: <[email protected]>
References: <CAMFjj72gqagv0cw7__THvXCXgAbAC=xb82SD4Sp-sGngx2V7qw@mail.gmail.com> <[email protected]>
Reply-to: [email protected]
Sender: [email protected]
Hi Stefan,

       There are thousands or perhaps tens of thousands of volts from the loop to ground.
If I grounded the loop with and there was a large potential difference, wouldn't that cause a large current to flow to ground and effectively shunt my signal to ground?

73 Warren



On Fri, Apr 26, 2013 at 1:44 PM, Stefan Schäfer <[email protected]> wrote:
Warren,

What is the voltage between the tree (GND) and loop? I thought that the voltages are rather small, i.e. below 100V, especially when a large loop is used. Isn't it possible to ground the loop?

73, Stefan

Am 26.04.2013 19:21, schrieb Warren Ziegler:


Just a quick report on a failure mode for LF TX antennas.
Last Fall my original TX loop made up of approximately 500 feet of RG-11 coax suspended from trees went open circuit (both center conductor and shield), some time later part of the wire actually came down. I had thought that abrasion from contact with the trees had eventually worn through it.

What I found was a little more interesting. Looking at the downed end, it appeared that the insulation had melted for a considerable distance and there were burn marks further up the cable. My hypothesis is that the outer insulation was abraded away and the coax shield came into contact with the tree limb causing the burning/melting.
Will try to get some pictures this weekend and put them up on my website.

Long term if one wants to operate at the kW level either better insulation or a better way of supporting the antenna than trees would be required!

--
73 Warren K2ORS
                WD2XGJ
                WD2XSH/23
                WE2XEB/2
                WE2XGR/1





--
73 Warren K2ORS
                WD2XGJ
                WD2XSH/23
                WE2XEB/2
                WE2XGR/1

 
<Prev in Thread] Current Thread [Next in Thread>