Return to KLUBNL.PL main page

rsgb_lf_group
[Top] [All Lists]
<prev [Date] next>
[Advanced]
 <prev [Thread] next>

Re: LF: Re: 136kHz LPF toroids?

from [Roger Lapthorn] [Permanent Link][Original]
To: [email protected]
Subject: Re: LF: Re: 136kHz LPF toroids?
From: Roger Lapthorn <[email protected]>
Date: Sun, 25 Jul 2010 20:53:27 +0100
Dkim-signature: v=1; a=rsa-sha256; c=relaxed/relaxed; d=gmail.com; s=gamma; h=domainkey-signature:mime-version:received:received:in-reply-to :references:date:message-id:subject:from:to:content-type; bh=moemDHbF8+zYBeBUpjD6DacRA4SVhYBVSW7K2Mxaqdg=; b=BC0kFhnPkpUgtWWquviFkwnYv4WxPfVAeocd5sMDjSWr4P+GyqdIyfi3aP5ub9dTJL booz33ilf36/RB1Hj1i0aVhM0TTwacF/hSrY7FO0XIPeVwO3uMi9ACBkIayfyMWwiUiT lq4Rra8z5oeyKvwmDiPUagTICqFhgoa25r+wI=
Domainkey-signature: a=rsa-sha1; c=nofws; d=gmail.com; s=gamma; h=mime-version:in-reply-to:references:date:message-id:subject:from:to :content-type; b=FadvcLpdAI7R7DXa0iwTH3fILbYmyiy2OrvaC1yBpYzgPnM0fWnExUNgV1V25ymzZp ny2z7V/8hRyycAvF1NcN6TxDfrZ65nekjWehAaHVNqf+915Weowc2f3S29fF88w3Qr/U Lc0ZmlfqLszcrUIcbZEI9PzBhgD9SLMP3WStU=
Domainkey-status: good (testing)
In-reply-to: <[email protected]>
References: <[email protected]> <002a01cb2c25$ed5da320$0601a8c0@xphd97xgq27nyf> <[email protected]>
Reply-to: [email protected]
Sender: [email protected]
All,

Thanks for the good advice already regarding LPF toroids for 136kHz. Sounds like a T68-2 or T157-2 (or something in between) should fit my requirements well. Mal, et al, my ERP is unlikely to exceed a few milliwatts on 136kHz, so don't worry about me putting out too much power :-)

Any suggestions on what inductor type to use for receiver input tuned circuit on 136kHz please?

73s
Roger G3XBM


On 25 July 2010 19:39, Gary - G4WGT <[email protected]> wrote:
Hi Mal,

You wrote :-
The aim on this band is for at least 1W erp

The maximum allowed ERP for this band (136kHz) is 1 watt ERP.

73

Gary - G4WGT.


On 25 July 2010 19:19, mal hamilton <[email protected]> wrote:
Roger
A T- 200 is ideal but maybe too large for u. Except you have a large antenna 20w is not enough on 137 for any serious impact.
The aim on this band is for at least 1W erp
de mal/g3kev
 
----- Original Message -----
Sent: Sunday, July 25, 2010 6:58 PM
Subject: LF: 136kHz LPF toroids?

Some advice please....
  1. I'm about to construct a 136kHz transverter with an output power up to 20W. What's the best choice of toroid for the TX output low pass filter inductors for this sort of power level?  Around 54uH is required and this is rather too much for a T50 (red) toroid that I used on 500kHz. I don't want anything too physically large if I can avoid it.
  2. Also, are there any readily available canned inductors (or toroids) suitable for use as the input tuned circuit on RX? Something like the KANK3333 inductors from Toko? Again, nothing too big unless this is a necessity for large signal handling.
Thanks in advance for inputs.

73s
Roger G3XBM

--
http://g3xbm-qrp.blogspot.com/
http://www.g3xbm.co.uk
http://www.youtube.com/user/g3xbm
G3XBM    GQRP 1678      ISWL G11088




--
http://g3xbm-qrp.blogspot.com/
http://www.g3xbm.co.uk
http://www.youtube.com/user/g3xbm
G3XBM    GQRP 1678      ISWL G11088
[More with this subject...]
<Prev in Thread] Current Thread [Next in Thread>
Previous by Date:  Re: LF: Re: 136kHz LPF toroids?, Gary - G4WGT
Next by Date:  Re: LF: Re: 136kHz LPF toroids?, Stefan Schäfer
Previous by Thread:  Re: LF: Re: 136kHz LPF toroids?, Stefan Schäfer
Next by Thread:  Re: LF: Re: 136kHz LPF toroids?, Stefan Schäfer
Indexes:  [Date] [Thread] [Top] [All Lists]