Return to KLUBNL.PL main page

rsgb_lf_group
[Top] [All Lists]

Re: LF: 500 kHz WSJT JT4A

To: [email protected]
Subject: Re: LF: 500 kHz WSJT JT4A
From: Gary - G4WGT <[email protected]>
Date: Thu, 21 Jan 2010 22:10:14 +0000
Dkim-signature: v=1; a=rsa-sha256; c=relaxed/relaxed; d=googlemail.com; s=gamma; h=domainkey-signature:mime-version:sender:received:in-reply-to :references:date:x-google-sender-auth:message-id:subject:from:to :content-type; bh=YtPWJcoZwzQzB3veh3TIYa02M6QwKtFTWSJoUvpWEm4=; b=beqDbIDmykeeLqTVrkfMMtemBP+IDNaamGkSvHAV13PbQlGEceO3WppB7RBqHlep2F DH+npYL43QhB1toix98iHKQam4fm8AZHKdoQ5Qin3z+7IxfpUaJAHx029RYDJAUBuM5N 8evCkqtbJO8Z76rmsrbyfAH07/AtAylljK7xQ=
Domainkey-signature: a=rsa-sha1; c=nofws; d=googlemail.com; s=gamma; h=mime-version:sender:in-reply-to:references:date :x-google-sender-auth:message-id:subject:from:to:content-type; b=m49lUqN730587IaYkt8ajSNG7IZGhZS1MVBGtu+QVnPcKyFyQ6kqeHLD4FERNO8kcX /hRvqgsOItX6d3Sgbk5Vi+qBimETo6LG8zGIjfcWFtnveKJncz/5OnEHtB3Uy0Q50mED pHSd2rgAogUXypfnecgDXaeJcSETlZNssAsMM=
Domainkey-status: good (testing)
In-reply-to: <[email protected]>
References: <[email protected]> <[email protected]> <[email protected]> <[email protected]> <[email protected]>
Reply-to: [email protected]
Sender: [email protected]
OK Andy,

Any suggestion is welcome but yes I do have it set for JT4A, I am currently on 80m decoding fine with JT65A.

Looked at the Rate in & out in setup/options & are both set for 1, the rate shown at the bottom left is usually very close to 1.0003. I would say that is OK.

I will try again tomorrow.

Thanks again.

Gary - G4WGT.

2010/1/21 Andy Talbot <[email protected]>
may be egg-sucking-lecture, but you have got JT4A set haven't you?.  Not B...G.
2010/1/21 Gary - G4WGT <[email protected]>
Andy,

You wrote :-
Watch & check your sampling rate calibration. for this mode.

Is that displayed in the box at the bottom left, if so then it is always within the recommended figures. I read in the user guide to watch those figures for stability & I have never seen it go outside the range specified in the manual.

There is an "Enable Diagnostics" in the setup menu but no description in the use guide (WSJT6), it must be an addition in 7.03 but not documented. Is that of any help to me?

73

Gary - G4WGT.


2010/1/21 Andy Talbot <[email protected]>

Watch & check your sampling rate calibration. for this mode.

Andy
www.g4jnt.com

This email has been scanned for damaging side-effects by the health and safety police, is guaranteed to contain no substances hazardous to health, but may contribute to dissolving the nether and polar regions


2010/1/21 Gary - G4WGT <[email protected]>
LF,

Station calling about 503.670 kHz but no decode. Not sure why :-((

Gary - G4WGT.



2010/1/21 Gary - G4WGT <[email protected]>
LF,

I am currently transmitting a WSJT JT4A test signal on 503.600 kHz at each even minute, the ERP is estimated at 200 mW.

In a while I will change the message to a CQ call & watch for any JT4A replies.

73,

Gary - G4WGT.








<Prev in Thread] Current Thread [Next in Thread>