Hi All, After actually finding & repairing the cause of the grabber PC total failure I have restarted the LF/MF grabber :- http://myweb.tiscali.co.uk/wgtaylor/grabber2.html http://myweb.tiscali.co.uk
Hi Gary, Thanks for the grabber service! We will leave some traces there soon. 73, Stefan Am 07.09.2014 18:02, schrieb Gary - G4WGT: Hi All, After actually finding & repairing the cause of the grab
Hi All, I am pleased to announce that my LF-MF-VLF grabber is finally fully fuctional again at :- http://myweb.tiscali.co.uk/wgtaylor/grabber2.html Problem was due to PC main board failure. The board
They are lmeasured in different ways. The noise measurement (black trace) is measured over the complete preceding 1 nminute period so approximates a good average. The signals, however, are measured o
Hi Richard, I must admit that I don't know, I just run the software & don't carry out any processing of the data. But, I seem to remember that Andy once stated that the noise trace is carried out at
In a message dated 07/07/2009 20:54:29 GMT Standard Time, [email protected] writes: Please have a look & I will be interested in your comments. Looks good to me. Thanks for the resource. On the thi
Hi, In an attempt to improve the performance of Grab1 & Grab2 at http://myweb.tiscali.co.uk/wgtaylor/grabber2.html I have replaced the RF pre-amp before the Softrock Lite SDR which I use to receive t
The red one is my 503.7kHz beacon at the quarter hour + 4 minute intervals, using teh same Tx format as teh GB3RAL/WES/ORK beacons. Green abd blue slots are availalble for other beacons, black is teh
Thank you Andy, I was about to place an answer to David's query, his question has prompted me to add a little more info on the grabber page. Thanks to you both. Gary - G4WGT. Gary Why don't the blue
Hi LF, As an experiment I have introduced a new grabber page. Please have a look & I will be interested in your comments. http://myweb.tiscali.co.uk/wgtaylor/grabber2.html 73, Gary - G4WGT - IO83QO.
Andy, LF, Thank you Andy, I was about to place an answer to David's query, his question has prompted me to add a little more info on the grabber page. Thanks to you both. Gary - G4WGT. The red one is
Hi all at LF, I have modified my 136kHz grabber to show split screen displays of both the TA & EU frequencies. http://myweb.tiscali.co.uk/wgtaylor/grabber2.html I hope this is useful. -- 73, Gary - G
Hello Gary, Excellent! Many thanks. I'll try now to leave a trace there but probably there is no chance to that time. BTW regarding upload size limitations by the ISP: You could upload a much smaller
LF, In view of recent 136.172kHz QRSS activity I have changed the scroll rate on Grab 3 to QRS30. http://myweb.tiscali.co.uk/wgtaylor/grabber2.html 73 Gary - G4WGT.
Hi all, I have extended the frequency range of my Grab 3 to cover from 137.800kHz to 137.300kHz. This will show the QRS, WSPR & Opera sections. http://myweb.tiscali.co.uk/wgtaylor/grabber2.html 73, G
Hi All, Sorry to any grabber watchers........2 short duration power cuts last night both causing PC to re-boot but on inspection this morning found that a main grabber sound card had been destroyed.
Hi All, Progressing slowly with updates & active antenna tests. The antenna is not yet in it's permanent position on the mast & is lower than normal. I have added another window, this is split screen
Hi Gary, It looks like "one pixel per FFT bin" is disabled. This makes it nearly impossible to read DFCW signals... I think for QRSS-60, 136172+-3 Hz is enough to display all the activity. Just an id