|
Uwe,
Unfortunately no decodes here. I see 2 decodes by you
self in the upper Opera window.
Everything is running fine in my oppinion;
Mini Wipe battery is loaded, CPU use
indicator abt. 10 - 25%, VU meter indicator
jumps from 9 tot 12h, and digital VU shows abt. -30 / -55
dB.
Input level is O.K. (with input gain on max is overload
easy)
Well... next cycle end soon. Fingers crossed...
:-)
PA1SDB. Peter.
----- Original Message -----
Sent: Monday, December 30, 2013 10:35
PM
Subject: Re: Re: Re: VLF: Uwe
Opera-4H
Hi Peter and Graham, the TX is still on the air.the next esquenz
will start at abt 2350utc.
Im playing around on the RX side and I did so during the test. may be
that’s the reason for the anomalies in the RX window of Opera. Pse
see:
http://dj8wx-dl.de/opera4a.jpg
SpecLab works fine here.
GL
Uwe/dj8wx
Von: [email protected]Gesendet:
30.12.2013 22:00 An: [email protected]Betreff: Re: Re: VLF:
Uwe Opera-4H
When stops/starts the old/new cycle
Uwe ?
----- Original Message -----
Sent: Monday, December 30,
2013 5:50 PM
Subject: Re: Re: VLF: Uwe
Opera-4H
Somehow I did not got your mail
Uwe,
Now I read this via
Graham...
A Local test (2 PC's few meter
appart) with OPERA 8 KHz did fail.
No decode's.
I think that VLF PC was to busy with
4 SL's running on that PC to.
Just few minutes ago (17h45) I did
configure a OPERA only PC at 8 KHz.
Lets try to make that first DL - PA
on 8KHz :-)
73's Peter - PA1SDB
----- Original Message -----
Sent: Monday, December 30,
2013 3:01 PM
Subject: Re: Re: VLF: Uwe
Opera-4H
Uwe
Well that's the first past the
garden gate ! unless the drive is
3Kmt long hihi
Fade shows 32 % ? that's
only 2/3 of the tx time line
, was the Tx stopped ?
still at -2 dB s/n thats still ~ +48 dB
qro !
73-G,
Sent: Monday, December 30, 2013 2:46 PM
Subject: Re: Re: VLF: Uwe Opera-4H
HI Peter,
I changed the TX QRG to 8912.5Hz running SpecLab in
Op-4H (ASK0) mode and made a first test with positive result.
the RX was located in 3km distance - Opera v.1.5.0 , RX aerial a
10m wire connected to the soundcard.
TX output pwr about 1W. pse see:
http://dj8wx-dl.de/opera3.jpg
I think we should have a try as you are my nearest
station rxing VLF.
Now Im increasing the PA output pwr to 500Wrms.
GL
Uwe/dj8wx
Von: [email protected]Gesendet: 29.12.2013 09:45 An:
[email protected]Betreff: Re: VLF: Uwe Opera-4H
Hello Uwe, Markus,
VLF
Nothing was seen or detected here
from your transmission in OPERA mode either.
No recognizable trace at
all.
While you're continuous
unmodulated signal almost overloads my soundcard input.
73's Peter - PA1SDB
----- Original Message -----
Sent: Saturday, December
28, 2013 9:08 PM
Subject: Re: VLF: Uwe
Opera-4H
yes Markus, I have had the screen showing the SecLab
components in my focus whilst doing other jobs - for
hours.
Now the carrier only mode is on the air.
Until next test
GL
Uwe/dj8wx
Von: [email protected]Gesendet:
28.12.2013 19:07 An: [email protected]Betreff:
VLF: Uwe Opera-4H
Uwe,
sorry, nothing
was seen or detected here from your transmission today. Not a
trace. Der erste
Versuch ist meist nicht genuch (Didi
Drahtlos).
Yes I noticed the
good trace on Paul Nicholson's spectrogram http://abelian.org/vlf/fbins.shtml#p=1388246400&b=080&s=sp.
Just look at it
the other way round: You did send a long carrier, only with some short
interruptions. But the gaps were so short that the spectrum didn't
notice them ;-)
More seriously:
Compared to a
continuous carrier, with 50% duty cycle the
carrier component is still there but 6 db down (half average voltage).
In terms of power, on average you are spending 50% of the
power. 25% (-6 dB) goes to the central carrier, and the
other 25% into the AM sidebands carrying the
message.
What I
find strange is that the spectrogram trace seems to have
jumped 28 mHz low, once near the beginning and again for
an hour around 14:30. Are you sure that your samplerate correction
had been engaged without interruption?
Best
73,
Markus
(DF6NM)
Sent: Saturday, December 28, 2013 3:05 PM
Subject: Re: Re: LF: Sending Opera with
SpecLab
OK.,
Markus, but the Todmorden grabber shows the signs.its a surprise for me.
I didnt expect it samples such relative short
signs. GL Uwe/dj8wx tks for the correction.
Von: [email protected]Gesendet:
28.12.2013 12:47 An: [email protected]Betreff:
Re: LF: Sending Opera with SpecLab
Uwe,
good news!
I'm watching and searching ;-)
Background noise
seems to be a few dB higher than the last couple of days, but we'll
see what's possible anyway. Unfortunately the OK2BVG
grabber website appears to be down at the moment.
Good
luck!
73, Markus
(DF6NM)
PS: In my
original mail, the Op-8 line in the speed table erroneously
contained an entry for Op-4. This has been corrected
beneath.
Sent: Saturday, December 28, 2013 12:14 PM
Subject: LF: Sending Opera with
SpecLab
Hi
all, the PA has been switched on. the next txt block will start
now. GL Uwe/dj8wx
Von: [email protected]Gesendet:
27.12.2013 15:47 An: [email protected]Betreff:
Re: Re: LF: Sending Opera with SpecLab
Hi Markus, Wolf, Stefan, Peter es all, tks for the
advice, Markus
now SpecLab is beaconing in mode Op-4H on
8969.99Hz
the PA is off until it is dry outside.
I keep your proposal txing btwn 0700 and 1400MEZ in mind,
Markus.
GL
Uwe/dj8wx/dj8CAT
|
