Return to KLUBNL.PL main page

rsgb_lf_group
[Top] [All Lists]

LF: A burning affair

To: "LF-Group" <[email protected]>
Subject: LF: A burning affair
From: "Dick Rollema" <[email protected]>
Date: Fri, 30 Jul 1999 14:21:21 +0200
Cc: "Ger van Went, PA0GER" <[email protected]>, "Pieter Bruinsma, PA0PHB" <[email protected]>, "Gerrit Jan Huijsman, PA0GJH" <[email protected]>, "Klaas Spaargaren, PA0KSB" <[email protected]>
Reply-to: [email protected]
Sender: <[email protected]>
From PA0SE to All    
 
When last year I had completed my LF-station I measured the total series resistance of the aerial/earth-system at 61 ohm,
using a Wayne Kerr Radio Frequency Bridge type B601. The value was confirmed by measuring the loaded Q of the system.
 
For a check I measured again yesterday and found a surprising low 36.8 ohm! What could have made the change? The earth
resistance? In case of a small change it could have been. But almost halved? No. And then the penny dropped.
 
My aerial is a 2 x 20 m dipole with 11 m open line feeder. The feeder wires are strapped for LF. The bare wires enter the
shack through holes in the hardwood window-frame. Outside above the window is a panel made of some kind of pressed wood. The
bare wires touched the edge of the panel but I never worried about that. In the HF bands the voltage on the wires is never
very high and I considered the insulation resistance of wood high enough. In fact I never had any trouble on the HF bands
or on 160 m.
 
One evening last winter I was beaconing on 136.550 kHz when my wife came into the house in a state of alarm. "There is fire
outside the window of your shack!" I went outside and indeed in the rhythm of the morse code bright white fireworks could
be seen at the feeder entry point.
An investigation next morning showed that were the wires touched the panel, slots of several centimetres long had been
burned into the pressed wood. Also the holes in the window-frame were charred.
 
To improve the situation I enlarged the holes in the window-frame and inserted paxolin tubes that reach well outside the
pressed wood panel. I also replaced the bare wires by PVC covered wire where the feeders pass trough the paxolin tubes.
Since then no sparking or charring has occurred.
 
Obviously the poor insulation had increased the total series resistance to 61 ohm.
 
The capacitance of the aerial is 370 pF (reactance -j3.160 kohm at 136 kHz). So the reactance of the loading coil in parallel with a vacuum capacitor (set at a small value) is j3.160 kohm. The measured series resistance is 9.5 ohm so the unloaded Q is 333. The calculated series resistance of the aerial is 0.2 ohm. So the resistance of the earth is 36.8 - 9.3 - 0.2 = 27.3 ohm. Not too bad I think.
 
The aerial current had increased from 1.37 A at the beginning to 2.39 A now which means an increase of radiated power by
3.8 dB. The power fed to the aerial/earth-system is 2.12A * 2.12A * 36.8 ohm  = 162 watt. This is not too different from the
output of the transmitter which I measured at 175 W. DC input is 259 W so the efficiency of the class B amplifier is 68%.  
 
It all goes to show how important the insulation of the aerial at LF is. It has been said and written before over and over again but
it seems that an experience like I had is needed to really burn it in!
 
73, Dick, PA0SE
JO22GD
D.W. Rollema
V.d. Marckstraat 5
2352 RA Leiderdorp
The Netherlands
Tel. +31 71 589 27 34
E-mail: [email protected] From PA0SE to All
<Prev in Thread] Current Thread [Next in Thread>