Hi Andy I know JT2 and JT4 was a coming but from wich program 73 Ko, NL9222 Andy G4JNT www.scrbg.org/g4jnt Hi Andy, Thanks for sending me a copy of your message to the RSGB LF group. I will be very i
I was too fast again, it's found here http://www.w6cqz.org/ 73 Ko, NL9222 Andy G4JNT www.scrbg.org/g4jnt Hi Andy, Thanks for sending me a copy of your message to the RSGB LF group. I will be very int
henny van elst wrote: *capture wd2xsh/17* *time 3:00z* *antenne dx-10* *rec:rohde &schwarz* *henny pa3cpm* *73s Henny Dat gaat echt wel een heel stuk beter zo ;-) Ko -- avast! Antivirus: Outbound mes
mal hamilton wrote: Since there is no LF/MF news or acty I would like to know if anyone knows how the satellite scene is getting on. I have not seen any mention of satellite acty in Radcom for a long
mal hamilton wrote: Douglas Bader RAF pilot was flying spitfires during the last war without LEGS, also a wireless operator on a Lincoln bomber used his foot to send morse, after his hands were injur
[email protected] wrote: In a message dated 07/08/2008 10:31:28 GMT Standard Time, [email protected] writes: ......... And, if you have an infinite numbers of monkeys with a pen and paper, one of the
mal hamilton wrote: The CW part of 160 m is so busy tonite that it is hard to find a slot for a CQ. What a contrast to 600m, apart from a couple of operators, most do not know what CW sounds like!!!!
mal hamilton wrote: Tnx Jim for the info but in actual fact 200 hz is required and not only 6 hz as some have specified, in other words if there was other acty within the 200 hz bandwidth it would co
just installed WSPR 1.01, and read your signal on first try: 1952 -26 1.5 0.137500 0 M0BMU IO91 23 1956 -22 1.4 0.137500 0 M0BMU IO91 23 Is it possible to tell WSPR to listen on a different audio cen
Hi all, dj8wx is xmitting at 135,975kHz in WSPR mode, pwr abt 50mWERP. RX dial 134,475kHz (USB). regards Uwe/dj8wx/jo43sv Hi Uwe 2004 -23 0.4 0.135975 0 73 DE DJ8WX JO43 2008 -23 0.6 0.135975 0 73 DE
I am now transmitting a test WSPR beacon signal on 137.50kHz +/- (136.0kHz "dial frequency"), at 33% TX, about 300mW ERP. Any reports would be very welcome. Cheers, Jim Moritz 73 de M0BMU Hello Jim 0
I will be running the WSPR beacon again tonight on the same settings as before; 502kHz "dial frequency", RF out on 503.51kHz +/-, 1W ERP, 33% transmit. It will be QRV from around 2200utc and hopefull
I'll make DX beacons May, 1-2 on 137.778 from 1630z till 23z, on 136.320 from 23z till 0230z, same May, 2-3. QTH: Machta, KN97LN, sunset 1630z and sunrise 0215z (1 May) abt 5W ERP (100W output in Big
Thanks for the reports and spots overnight on the 500kHz WSPR beacon. I am currently (1215utc) running a WSPR beacon on 137.5kHz RF out, 136.0kHz "dial frequency", with about 100mW ERP. Any reports w
Walter und Marianne Staubach wrote: Dear MF, DI2AG is already on air in WSPR. QRG 505.090KHz, PWR 0.4W ERP. Duty cycle 33%. The beacon will be busy until tomorrow morning. 73 Walter DI2AG / DJ2LF Wal