Return to KLUBNL.PL main page

rsgb_lf_group
[Top] [All Lists]

LF: RE: Re: TXing WSPR on 630m on a Raspberry Pi, Stefan in QRP...

To: <[email protected]>
Subject: LF: RE: Re: TXing WSPR on 630m on a Raspberry Pi, Stefan in QRP...
From: "Dave G3WCB." <[email protected]>
Date: Fri, 27 Mar 2015 11:53:20 -0000
Dkim-signature: v=1; a=rsa-sha256; c=relaxed/relaxed; d=btopenworld.com; s=btcpcloud; t=1427457202; bh=bh83cDCw8m1+NKGyJqCordDYxbzkEx/ctssn+cuGLp4=; h=From:To:Subject:Date:Message-ID:MIME-Version:X-Mailer:In-Reply-To; b=MHpnEgnTaQPxkMsLNOtMJavEkvNabxHnYxk9+lBO7MtZEaogi1yBjbBmn8qKWVib2ODfvWn5CSCZelsfJcPVJx1fa6WH4uMw8JwC/OZ3NUqoRXxBoxTWu6anhe0eKT2l2KOyF+mZwaKhzc8CIiQFOxzSeKhZvJ6q5GfL/FFJMNM=
Importance: Normal
In-reply-to: <520562D5C7694FF69C20E595E00B793D@F6CNIToshiba>
Reply-to: [email protected]
Sender: [email protected]

Hi, Andy.
 
Thank you for the report. I'm running about 15W RF into a 5m high, 20m long "Tee" with two top wires. My antenna current is about 0,8A.
 
After Easter I will be QSY-ing to IO80 locator, and I hope to be running WSPR from there on 630m. The antenna situation in IO80 is not so good, so I will have to experiment with some "Stealth" antennas for MF!
 
73, Dave G3WCB IO91RM > IO80DI
 
-----Original Message-----
From: [email protected] [mailto:[email protected]]On Behalf Of Guyé André
Sent: 27 March 2015 10:26
To: RSGB LF Group
Subject: LF: Re: TXing WSPR on 630m on a Raspberry Pi, Stefan in QRP...

Hello Stefan.
 
Ok about your interesting test with 0.5 TX Power. Sorry, I cannot copy you on day time, due to high carrier QRM just on your transmitting QRG. On the way now, the G3WCB signal is good around 0 dB S/N, at about the same distance as you.
 
I am now transmitting 2 or 3 times to see the difference in ON7YD and OR7T reports.
 
You know that I am always transmitting QRP on MF. Maximum power is 3 Watts output TX. Now I have exactly the same power as your : 0.5 Watt. On night this winter I was mostly using below 0.1 Watt.
 
My large winter antenna (Inv L) is dismounted and I am using a single 25 meters vertical tube without top hat capacitance. The effeciency is around – 20 dB, so the PAR (apparent radiated power) is 5 milliwatt.
 
If you want to have real QRPP test, you can test WSPR at 500 micro watt PAR, and still have lucky reports up to 1500 km.
 
Best 73. Andy F6CNI – JN19QB
 
Sent: Friday, March 27, 2015 10:29 AM
Subject: RE: LF: TXing WSPR on 630m on a Raspberry Pi, Stefan in QRP...
 

Hi Stefan,

 

solid signal here, best decode was at -8dB!

 

73, Rik ON7YD - OR7T

 


Van: [email protected] [[email protected]] namens DK7FC [[email protected]]
Verzonden: donderdag 26 maart 2015 23:17
Aan: [email protected]
Onderwerp: Re: LF: TXing WSPR on 630m on a Raspberry Pi, Stefan in QRP...

Hi MF,

I'm now running the 7667 at 13.8V supply voltage. The MOSFET driver is easily keyed by the Raspi, directly with its rectangular output. I measured 0.5 W TX power at 50 Ohm. This is what i'm running tonite on 630m.
Not a real PA, just the Raspi and this IC in a DIL-8 case. Fascinating!...

73, Stefan


Am 23.03.2015 16:11, schrieb DK7FC:
Hi MF,

I've added a simple ICL7667CPA MOSFET-driver to the GPIO of the Raspberry. It's power supply is 5V coming from the GPIO itselfe. This leads to a 5V rectangular signal with lower output impedance. I've coupled the output matching circuit so that the output power is now 50 mW / 17 dBm, i.e. 7 dB more power then in my previous test.
Iamge:  https://dl.dropboxusercontent.com/u/19882028/MF/17dBm%20RPI%20WSPR.jpg

The beacon is running now on 475.685 kHz.

73, Stefan/DK7FC


Am 18.03.2015 21:45, schrieb DK7FC:
Hi MF,

Today i've got i 3rd Raspberry Pi. I quickly installed the WSPR softaware and since a few minutes i am transmitting WSPR-2 on 630m, my usual frequency 475.685 kHz.

I'm directly using the GPIO output pin, without an amp stage behind! The rectangular 3.3V output voltage is passing a cap and an isolation transformer (FT50-77) as well as a simple pi-filter, because it is a Raspberry pi! ;-)

See: https://dl.dropboxusercontent.com/u/19882028/MF/Raspberry%20Pi%20B%2B%20WSPR%20TX.jpg

I measured an output power of about 10 mW at 50 Ohm. It is now connected to my MF antenna and transmits in a 100% duty cycle. I still have to learn how to reduce it but this will not take long.

With 10 mW TX power i managed decodes by 3 stations now.

3 spots:

Timestamp Call MHz SNR Drift Grid Pwr Reporter RGrid km az
2015-03-18 20:32 DK7FC 0.475684 -21 0 JN49ik 0.01 DH5RAE JN68qv 345 98
2015-03-18 20:12 DK7FC 0.475685 -24 0 JN49ik 0.01 F1AFJ JN06ht 667 247
2015-03-18 20:06 DK7FC 0.475683 -27 0 JN49ik 0.01 DL1DBC JO41bi 217 349


Does someone have good ears to get a decode from me? :-) It is a challenge! :-)

73, Stefan/DK7FC

PS: The signal is so weak that my RX antenna frontend is not overloaded, so at that power level i can transmit and receive to the same time :-)
PPS: A small amp stage will follow soon, i intend to use an BS170 running at 5 V.



Avast logo

L'absence de virus dans ce courrier électronique a été vérifiée par le logiciel antivirus Avast.
www.avast.com


<Prev in Thread] Current Thread [Next in Thread>