Return to KLUBNL.PL main page

rsgb_lf_group
[Top] [All Lists]

RE: LF: RE: Transformer questions.

To: <[email protected]>
Subject: RE: LF: RE: Transformer questions.
From: "Clemens Paul" <[email protected]>
Date: Sun, 25 Jun 2017 14:19:54 +0200
In-reply-to: <[email protected]>
References: <[email protected]> <EFA843B116824E4B89B87C3BAAE2DB33@Clemens0811> <[email protected]> <1B7B7537AD024FBDAA5E898E3DF21AAB@Clemens0811> <[email protected]> <A1807AACE4FF4AA38C1FB06188042EB7@Clemens0811> <[email protected]>
Reply-to: [email protected]
Sender: [email protected]
Thread-index: AdLtInQe7qylbQ4YQkacS1MkBib2eQAiJI7Q
Hi Chris,

ok, I hope I have now understood your set up and what you may possibly want to 
change.
Present configuration:

>2  X  amps to combiner via 2 off 12 inches Teflon coax cables : Combiner
>to  LPF via 12 inches Teflon co-ax : Combiner to outside about 40 feet
>RG-213  co-ax  :  Outside  is impedance matching transformer on top of
>loading  coil / variometer : Impedance matching transformer to loading
>coil  via  12  inches  RG-213 : Loading coil feeds vertical section of
>antenna directly. 

And from an earlier post by you:

>>Can I wind the isolating
>>transformer as a 1 : 1 and do impedance matching (which changes with
>>weather / foliage growth) indoors using a tapped combiner auto
>>transformer? 

So you want to modify the combiner-autotransformer into a tapped one
and OTOH modify the tapped isolation transformer into a non-tapped 1:1 one.(?)

This would be not a good idea.
The combiner XFM would not work any more,the LPF would not work any more 
properly.
Both need to see 50 Ohm.
Even if you cancel out the antenna/feeder reactance by the loading 
coil/variometer you are left with a
very low real part of impedance of a few Ohm.
So beside the malfunction of the combiner and the LPF you would get a loss of 
about 2dB on the 40 feet
coax (assuming 2 Ohm for the real part).

73
Clemens
DL4RAJ 


 

>-----Original Message-----
>From: [email protected] 
>[mailto:[email protected]] On Behalf Of Chris Wilson
>Sent: Saturday, June 24, 2017 9:44 PM
>To: Clemens Paul
>Subject: Re: LF: RE: Transformer questions.
>
>Hello Clemens,
>
>It  is  between  the  outdoor end of the RG-1213 co-ax and the loading
>coil,  although  it's  not   1  :  1 at the moment, it has taps on the
>primary and the secondary to fiddle with.
>
>
>
>Saturday, June 24, 2017, 7:45:48 PM, you wrote:
>
>> And where is the 1:1 isolation transformer inserted?
>
>> 73
>> Clemens
>> DL4RAJ  
>
>
>
>
>
>
>-- 
>Best regards,
> Chris                            mailto:[email protected]
>
>
>
>---
>Diese E-Mail wurde von AVG auf Viren geprüft.
>http://www.avg.com
>



<Prev in Thread] Current Thread [Next in Thread>