Return to KLUBNL.PL main page

rsgb_lf_group
[Top] [All Lists]

LF: Class E etc

To: "[email protected]" <[email protected]>
Subject: LF: Class E etc
From: M0FMT <[email protected]>
Date: Mon, 11 Jun 2012 19:15:49 +0100 (BST)
Dkim-signature: v=1; a=rsa-sha256; c=relaxed/relaxed; d=yahoo.co.uk; s=s1024; t=1339438550; bh=ADX/7EihfDl8xc3DahPydLk0sGztb7x8eeCjVtcBrTw=; h=X-YMail-OSG:Received:X-Mailer:References:Message-ID:Date:From:Reply-To:Subject:To:MIME-Version:Content-Type; b=nUdfBKt8hUWpeb7hWfp3MBqWNwMw+IKmDeZUwI1rY05TqnXNA0q7pH8dbfDlBD4zfbn3C8V+6ZdH9tlLwpIFfrtA8Q96m2mjD3kODki6E8TZYWfHulz1SDqPTFWz7Y/rKmpOcHaa12iC2pzqObm9/ZWk4hr6dWtEPQ9vDw/Abv8=
Domainkey-signature: a=rsa-sha1; q=dns; c=nofws; s=s1024; d=yahoo.co.uk; h=X-YMail-OSG:Received:X-Mailer:References:Message-ID:Date:From:Reply-To:Subject:To:MIME-Version:Content-Type; b=VR/cMkUH2GJ7J0NC5/6+zoNGVeKcZYlkOYq+obFvOwOXBIFGCEk+vr78YpwFscRcYw/Y8Qk8mgU3eaverAEGmla560Knj9cMVzjjxLNWh9Djwwut+/cH2qRMQVh2NUolVVXSKLpYPbSXqWiAMtChuqjJDMc70wM/GU9HJ2zntXQ=;
References:
Reply-to: [email protected]
Sender: [email protected]
 
Hi Ken
 
Ha ha Stefan, how good is your Integration Ken?
 
Here are a couple of sites that should answer your questions. You need a good dummy load and a good oscilloscope. Setting the conditions for the amplifier is to do with  A/ the correct driver preferably using a FET drive chip (like TC4422 non and TC4421 inverting) that will turn the FET fully on and fully off on each cycle. Very fast rise time with accurate on off timing (mark / space). Ensuring the max permitted gate voltage for the FET is not exceeded otherwise they pop, look out for transients, a diode clamp helps.  B/ Setting the shunt capacitance and inductance in the drain circuit can be done empirically See article below. Then follow it with a low pass filter, although the output wave will be surprisingly clean. Calculating the values is difficult as you don't necessarily know all the starting parameters and in any case the result is going to wide of the mark. The site below will gives some starting values. Best to use 'Scope measurements to set the output conditions. You are looking for fast, very fast On / Off rise times. Gate drive and understanding the drain circuit is the key.
These amplifiers are capable of incredibly good efficiency well above a dodgy class C amp. This means the heat dissipation from the FET is very low at high power giving cool heat-sinks!
 
The GW3UEP (do a web search) single ended design is capable good efficiency and high power depending upon the FET used and Drain supply voltage. I have modified one to run reliably at 140watts and is capable of almost twice that into a dummy load with a heat sink that is fairly cool. Adjusting L and C empirically using the 'scope to get the correct drain wave shape for max efficiency is the way to go. The article below shows you what you are looking for. I set my TX up into a 50 Ohm dummy load adjusting L and C to get the correct drain wave shape on the 'scope then measuring the peak voltage across the Dummy load. I then transfer my connector from the Dummy load to the input of the tuned transformer in the antenna up-lead. I adjust the coupling link to give the same peak voltage across the tuner link turns. You are not looking for maximum peak just the sames as across the dummy load indicating a 50ohm match. This is done by either adding or reducing the number of turns (about two turns) along with bringing the the transformer to resonance by measuring the peak up-lead current, here you are looking for the maximum peak.  
 
Oh yes and WIMA high voltage high value capacitors from Maplin work well.
 
Read the articles and search info on class E amplifiers. 
 
 
For some bed time reading but ignor the math look at the Tuning Procedure and the pictures at the end which tell it all really..... http://www.cs.berkeley.edu/~culler/AIIT/papers/radio/Sokal%20AACD5-poweramps.pdf
 
For design ideas
 
For a good practical circuit for a single ended amp that  is a scalable surefire design, no need to reinvent the wheel.
 
For antennas and antenna feed methods a "look no where else site"
 
73 es GL Pete M0FMT IO91UX
<Prev in Thread] Current Thread [Next in Thread>