Return to KLUBNL.PL main page

rsgb_lf_group
[Top] [All Lists]

LF: Re: Tree current

To: <[email protected]>
Subject: LF: Re: Tree current
From: "Hugh_m0wye" <[email protected]>
Date: Tue, 12 Jun 2007 11:39:07 +0100
Delivered-to: [email protected]
References: <[email protected]> <000901c7aa26$ecfaff60$82147ad5@w4o8m9> <000d01c7aa8c$6d692860$7c0d7ad5@w4o8m9> <[email protected]> <001301c7acd6$14f492e0$15337ad5@w4o8m9>
Reply-to: [email protected]
Sender: [email protected]
Hi Jim,
What an interesting experiment, and illuminating, although it told us what we already suspected, that lush foliage makes a nice garden, but rather spoils RF performance.

I have not come across the Rogowski coil before - does it work both ways - that is ,can you induce RF current into a tree trunk by applying an RF voltage to the coil ? Probably not very efficient, but you can probably see where I'm going with it !

The Rogowski coil seems to be rather like the signal clamps used to measure currents in power cables without actually connecting to them - but without the iron core.
Hugh M0WYE





----- Original Message ----- From: "James Moritz" <[email protected]>
To: <[email protected]>
Sent: Tuesday, June 12, 2007 10:43 AM
Subject: LF: Tree current


Dear LF Group,

It has often been said that trees surrounding an LF vertical antenna can be
responsible for a substantial proportion of  the antenna loss, and  at my
QTH there are several trees that have gradually been getting bigger over the
years, so I decided to try to measure how much RF current was actually
flowing in some trees.

To measure the tree current, I used a Rogowski coil - this is like a
toroidal RF current transformer, but without the magnetic core; instead of
measuring the secondary current, the open-circuit voltage across the
secondary is measured, and is proportional to the total current flowing
through the area enclosed by  the coil, the number of turns, the area of
each turn, and the frequency. My Rogowski coil used 1.2m of rubber hose as a
former, with about 500 turns of insulated wire, and had a scale factor of
around 100mV out = 1A in. I measured the voltage with a SPM-3 selective
voltmeter. The advantage of this type of current sensor is that the loop of
flexible hose former can be made large enough to fit round a tree, and can
be opened out, wrapped round the tree to be measured, and closed up again. A practical difficulty is that the output is quite small compared to a normal
current transformer, and an aluminium foil electrostatic shield had to be
added in order to reduce the effect of pick-up of the intense E-field
directly under the antenna. This did not entirely eliminate the problem, but
reduced it to a reasonable level.

I measured the current near ground level in the trunks of 8 trees - these
are scattered around within about 10m horizontally of the antenna, with
heights of about 5 - 10m (antenna height is around 9 - 11m). With an antenna
current around 4A, the currents ranged from 50mA to 190mA, with the total
for the 8 trees being 930mA. Generally, trees closer to the antenna and with
bigger areas of foliage had higher currents, as you would expect.

The 8 measured are only a sample of the small trees and large bushes in and around my garden, also at about 20 - 40m distance there are larger trees all
around my QTH as well. So it seems likely that a large fraction of the
electric flux of the antenna is intercepted by a tree at some point, and a
substantial proportion of the total antenna current is flowing to ground
through trees. Since wood is a poor conductor, it is not surprising that
trees close to the antenna increase the loss resistance. But also, current
flowing vertically in the trees will contribute to the overall radiation of
the antenna. However, since a current flowing "up" the antenna will be
flowing "down" the tree, and the spacing of tree and antenna is a very small
fraction of a wavelength, the effect of the tree current will be to partly
cancel the overall radiation, and so reduce  the radiation resistance. If
the current flowing in the trees is a large fraction of the total antenna
current, and the height of the trees is comparable with the antenna height,
one could expect a substantial reduction in radiation resistance and
effective height of the antenna, as the field strength measurements I made
last week would seem to indicate.

Cheers, Jim Moritz
73 de M0BMU






<Prev in Thread] Current Thread [Next in Thread>