Hi Stefan, Markus and Group, Thanks for looking Stefan. The ERP was down until the second Decca module was switched in at 2330 bringing the output power from 150 to 450 watts (3.2 amps to the aerial.
Dear Group, QRV again tonight. QRSS30 and seeking comments (especially unfavourable ones) on accuracy, drift and keying coherence. Vern's grabber is capturing them well at the moment. Thanks again, V
Thanks Jay. I cant always see the sigs on your grabber and think perhaps the aerial does not radiate as well to the west. 73 Joe Joe A look from closer in ... http://www.w1vd.com/grabber.html . Jay W
Hi Joe, looks like carrier stability was good while the signal was weak, but deteriorated after 2 UT. DDS affected by QRO? Best 73, Markus (DF6NM) From: [email protected] Sent: Thursday, June 06, 2013 1:
Joe A look from closer in ... http://www.w1vd.com/grabber.html . Jay W1VD WD2XNS WE2XGR/2 Hi Stefan, Markus and Jean Pierre F1AFJ (Grabber service), Thanks for the report, Stefan. I am happy you have
Hello Joe, Sorry, can't see you here. Nothing at DF6NM too... Is your ERP on the usual level? I remember our QSOs in QRSS-3... Good luck anyway! Maybe you will have chances in Venezuela: http://dl.dr
Thank-you Michel for the helpful report. It seems as if your RX is working well. 73 Joe VO1NA Hi Joe, After refurbishing the 137 kHz preamp, I'm back on LF - Rx only - The wideband 455 kHz ceramic fi
Hi Gary, Thank-you for the report, caputure and for running your FB grabber. I look for sigs on your grabber quite frequently to check the TX. The TX will be on again tonight, (without chirps I hope)
Joe, ok, then here comes a particularly un-welcomed report ;-) The problem seems to be solved, and this morning your trace appeared perfectly focused in the narrow spectrogram. The frequency is 13777
Hi Stefan, Markus and Jean Pierre F1AFJ (Grabber service), Thanks for the report, Stefan. I am happy you have something nice to say about my sigs. Its good that they are reaching you when we are so c
Thank-you, Michel. Good conditions and no mention of a chip, nor could I see one on your spectrum. Yesterday I changed the TX and hopefully fixed the chirp and maybe the phase glitches? There are sti
Hi Joe, Michel's excellent capture of your signal prompted me to check my over-night grabber saves & found your signal showing up for a long period of time from 00:50utc to about 03.30utc on my QRS03
Hi Joe, After refurbishing the 137 kHz preamp, I'm back on LF - Rx only - The wideband 455 kHz ceramic filter has been replaced by a 600 Hz mechanical filter, mainly to improve the RX's dynamic. I do
Markus, Thank-you for mentioning this problem. If it's QRO -> DDS it's likely due to shoddy construction technique by the operator! When this has been dealt with, we can try some OP32. 73 Joe Hi Joe,
Hello Joe, Gary's excellent capture of your signal prompted me to check my over-night grabber saves & found your signal showing up for a long period of time from 00:50utc to about 03.00utc. The best
Hi Joe, your QRSS signal was visible on my grabber last night, best between 2:16 and 2:40. As Stefan noted, SNR was somewhat lower than it used to be, but this may be due to conditions, or my RX bein
Joe Many times the rx antenna pattern is directed to the west. The 15 - 20 dB f/b can drop your sigs into the noise. Jay W1VD WD2XNS WE2XGR/2 Thanks Jay. I cant always see the sigs on your grabber an