Also very noisy in TheYukon. Red bar with gain at lowest setting. One LORAN line and two Dahs on 76.2, captured at ~11:20, and they look to strong to be ZL. J.
Ed, I have been beaconing on 137778.1 and 137778.25 24/7, and am making a special effort to have my amplifier in place before the ZL tests this weekend. Would it be possible for you to move your plan
Bob, ZL QSO group, and onlookers. :o) Not much cance of reception from ZL, but the beacon is on anyway. The station is running less than 1/2 W ERP, so if any distant stations see traces from here it
Hello Friends, VY1JA has begun beaconing with the callsign, VY1JA sent on standard CW at 12wpm followed by a single, "J" on DFCW120. This is repeated 24/7 on ~137778.1 and 137778.25 for now. The freq
Bob, VY1JA beacons 24/7 on ~137778 unless someone asks for a change in frequency or asks for me to listen for them. The main purpose in my experiment is to prove non-interference with Power Line Carr
All 500 kHz ops. I do not know how well my 137 kHz antenna will work as a receiving antenna on 500, but tonight will be my first attempt to receive there. Naturally, the beacon will be QRT on 137 to
This beacon here will change to DFCW 120 second dit also. The frequency is~137778.2 sending my entire call, VY1JA. If it should be moved up or down in frequency, someone please let me know.which way
Laurence, Good luck watching. The beacon is on ~137778.07 and .22. I do not know if .15 is too much split.... Is there a standard?. It is DFCW120, sending "VY1JA" as usual. It is tuned a little lower
Bob, VY1JA will be operational DFCW on the dit length and any frequency you choose which is not going to be occupied by either LORAN or another amateur station. Please help coordinate. Thanks, J. vy1
Hello Tech types. While I am working on the amp, I noticed that some of the FET drive circuits are fed directly from a driver device (G3YXM circuit p66 LF Today) and some use a blocking capacitor fol
Mike, Here is the last shot before I go to bed. I was on 20 meters and working EU. I switched to 505 and was copying WD2XSH/20 with very little noise and a good signal.... ON MY 20 METER BEAM! I set
Hello, Congratulations, First into Yukon. WD2XSH/20 normal speed CW on 505 into Yukon. Steady signal easy copy ....about 529 I hear another carrier dropping from time to time, but no callsign. J.
Hello All, especially 500 kHz. ers. "Well done" to all who have been pioneering 500 kHz.. There has been a lot of traffic on the reflector for 500, and that is to be expected because it is the new th
Joe, Using computer generated DFCW tones of 1000 and 1015 Hz into the microphone connector of a TS450 in SSB mode to generate DFCW works well. Divide the frequency of the DFCW at 13.776 MHz. output b
Sorry, that is a U not a Z. Someone else. J. -- Original Message -- From: "J. Allen" <[email protected]> To: <[email protected]> Sent: Saturday, 2007/03/31 12:19 Subject: LF: Re: ZL Te
Mike, I am sorry for leaving your name off of the communications... I just realized that I had been addressing all of them to Bob. There must be short circuits in my think bucket.... :o) J.
Bob and All, Reception not quite as good overnight, but still good. If you look closely, you will see the two screen captures were added so that they represent a continuous time line. Good work, ZM2E
