From: Roman <rw3adb@yandex.ru>
To: DK7FC <rsgb_lf_group@blacksheep.org>
In-Reply-To: <1893481215.20151013103725@chriswilson.tv>
References: <858532982.20151012141313@chriswilson.tv> <561BC13C.6070603@posteo.de> <1893481215.20151013103725@chriswilson.tv>
Subject: LF: CONGRATS
MIME-Version: 1.0
Date: Tue, 07 May 2019 08:39:46 +0300
Message-Id: <5360211557207586@iva8-582db1f60497.qloud-c.yandex.net>
Content-Transfer-Encoding: 7bit
Content-Type: text/plain
Sender: owner-rsgb_lf_group@blacksheep.org
Precedence: bulk
Reply-To: rsgb_lf_group@blacksheep.org


CONGRATS with the Day of Radio Chris!
True Alexander Popov!
Magic power of Radio bless us!
Henrich hertz mit uns!


73!
Roman

> Hello DK7FC,
> 
> Monday, October 12, 2015
> 
>> Hello Chris,
>>
>> My congrats!
>> Timestamp Call MHz SNR Drift Grid Pwr Reporter RGrid
>> km az 2015-10-12 14:14 2E0ILY 0.137500 -19 0
>> IO82qv 5 DK7FC JN49ik 878 111
>> That's really a good signal for that time. And i have a lot of QRM inside the 200 Hz wide WSPR-band!
>>
>> What antenna and power do you have?
>>
>> 73, Stefan
> 
> Thank you all for the congratulations and reports. Very early days
> yet, and many improvements need making. The aerial is my HF horizontal
> quad wire loop, up about 25 feet max, fed in a corner by my bungalow,
> (its lowest point too, so not ideal...), using the shorted windowed
> ladder line as the vertical. A six foot long ground spike near the
> feed point is the only earth. I want to raise the loop higher, add a
> ground wire under the perimeter, and add more ground spikes too. I may
> try using a grounded electric fence as an addition too, it runs almost
> underneath one leg of the loop.
> 
> As this is also my HF aerial I need to add some sort of relay to
> disconnect the shorted feeder from the LF matching coil and connect to
> a balun for feeding my HF stuff. Right now I can either use HF or LF
> and changing means a trip outside and much fiddling about. I am
> thinking of using an active whip and separate receiver for LF
> reception and a grabber though.
> 
> I need to improve matching and resonance slightly, but intend changing
> the feeder co-ax to the aerial for something less temporary. I built a
> scopematch and see the following right now, so room for improvement I
> feel:
> 
> http://www.chriswilson.tv/scopemeter-tx-full-power.jpg
> 
> The driver is the DRV output at 1mW from my TS-590 feeding a W1VD pre
> amp and W1VD frequency doubler, then running a G3YXM FET amp.
> 
> I noticed a hot smell from it last night, then it blew the RCD trip on
> the house electric panel. It ran again, but again on higher power
> ranges it did the same again. as it has over current and high SWR and
> drive loss safety cut outs I suspected something in the power supply,
> and indeed, it seems the toroidal mains transformer was getting hotter
> than I would have liked. I am wondering it it has an internal
> intermittent short? I may high pot test it later.
> 
> My other issue is I have modded my TS-590 to use a VK3HZ GPS locked
> master oscillator, fed from my Trimble Thunderbolt GPS.
> 
> http://www.vk3hz.net/XRef/XRef_Home.html#XRef-Vx
> 
> It has worked perfectly for months. But now I am TX'ing on 136kHz it
> is picking up RF, either into the Thunderbolt GPS itself, or a divider
> board that offers divisions of 10MHz for other uses in the shack. I
> see the square wave at 10MHz from the divider go crazy on my scope
> when I TX, so I am not using the GPS locked oscillator and find my
> signal is 3Hz off without it running. I am trimming on the actual rigs
> frequency setting to compensate.
> 
> So a few improvements to play with, and the issue of the GPS locked
> oscillator to fix. But I am over the moon to be finally able to TX
> rather than just listen.
> 
> A big step for me has been taken though! All the best.
> 
> --
> Best regards,
> Chris mailto:chris@chriswilson.tv
-- 
73!
Roman, RW3ADB